Home › BODY › WINDSHIELD / WINDOWGLASS › WINDSHIELD GLASS

WINDSHIELD GLASS > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 WINDSHIELD GLASS STOPPER
  1. Apply Primer G to the glass where the stoppers will be installed.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



    B073410E02
  1. Install 2 new stoppers onto the glass as shown in the illustration.

    Standard measurement:
    Area
    Specified Condition
    a
    40.0 mm (1.575 in.)
    b
    7.7 mm (0.303 in.)
    c
    12.5 mm (0.492 in.)



2. INSTALL NO. 1 WINDSHIELD GLASS STOPPER


B106096E03
  1. Install 2 new stoppers to the vehicle body as shown in the illustration.



3. INSTALL WINDOW GLASS ADHESIVE DAM
  1. Apply Primer G to the glass where the glass adhesive dams will be installed.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Remove the peeling paper from the adhesive part of the dam. Install the dam (adhesive side) to the glass (Primer G area), but exclude the spacer area A as shown in the illustration.


    B073411E01

    Standard measurement:
    Area
    Specified Condition
    a
    7.0 mm (0.276 in.)
    b
    27.5 mm (1.083 in.)



4. INSTALL WINDSHIELD GLASS


B106104E03
  1. Position the glass.

    1. Using suction cups, place the glass in the correct position.

    2. Check that the entire contact surface of the glass rim is perfectly even.

    3. Place matchmarks on the glass and vehicle body on the locations indicated in the illustration.

      HINT:
      1. Placing matchmarks is only necessary when installing new glass. If it is the reused glass, matchmarks should already be present.
      2. When reusing the glass, check and correct the matchmark positions.

      NOTICE:
      Check that the stoppers are attached to the vehicle body correctly.

    4. Using suction cups, remove the glass.



    B106085E04
  1. Using a brush, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply primer to the adhesive.
    3. Throw away any leftover primer.
    4. Do not apply too much primer.



    B073412E03
  1. Using a brush or sponge, apply Primer G to the contact surface of the glass.

    HINT:
    If the primer is applied to an area that is not specified, apply white gasoline to a clean cloth and wipe off the excess primer.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



    B073413E01
  1. Apply adhesive to the glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or Equivalent


    1. Cut off the tip of the cartridge nozzle as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.

    3. Apply adhesive to the glass as shown in the illustration.

      Standard measurement:
      Area
      Specified Condition
      a
      12.5 mm (0.492 in.)
      b
      8.0 mm (0.315 in.)
      c
      3.0 mm (0.118 in.)



    B106104E04
  1. Install the glass to the vehicle body.

    1. Using suction cups, position the glass so that the matchmarks are aligned. Press it in gently along the rim.

    2. Lightly press the outer surface of the glass to ensure that it is securely fit to the vehicle body.

      NOTICE:
      1. Check that the stoppers are attached to the vehicle body correctly.
      2. Check that the vehicle body and glass have a small gap between them.

    3. Hold the glass in place securely with protective tape or equivalent until the adhesive hardens.



5. INSTALL WINDSHIELD MOULDING OUTSIDE
  1. Using a brush or sponge, apply Primer G to the glass where a new moulding will be installed.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.

  1. Align the moulding's marks with glass notches and install the moulding before the adhesive dries.

    NOTICE:
    Do not drive the vehicle for the amount of time written in the table below.

    Minimum time:
    Temperature
    Minimum time prior to driving vehicle
    35°C (95°F)
    1 hour 30 minutes
    20°C (68°F)
    5 hours
    5°C (41°F)
    24 hours



6. INSTALL COWL TOP VENTILATOR LOUVER RH


7. INSTALL COWL TOP VENTILATOR LOUVER LH


8. INSTALL FRONT WIPER ARM LH


    I040975E01
  1. Clean the wiper arm serration with a round file or equivalent (when reinstalling).

  1. Clean the wiper pivot serration with a wire brush.



    I040976E03
  1. Install the front wiper arm LH with the nut so that the front wiper blade comes to the position shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    HINT:
    While installing the nut, hold down the arm hinge by hand.



9. INSTALL FRONT WIPER ARM RH


    I040977E03
  1. Clean the wiper arm serration with a round file or equivalent (when reinstalling).

  1. Clean the wiper pivot serration with a wire brush.

  1. Install the front wiper arm RH with the 2 nuts so that the front wiper blade comes to the position shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    HINT:
    While installing the nut, hold down the arm hinge by hand.

  1. Operate the front wipers while spraying water or washer fluid on the windshield glass. Ensure that the wipers function properly and there is no interference with the body.



10. INSTALL FRONT WIPER ARM HEAD CAP


11. INSTALL HOOD TO COWL TOP SEAL


12. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)


B113835E01
  1. Install the mirror in the direction of the white arrow.

  1. Install the cover as shown in the illustration.



13. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)


B056435E05
  1. Install the mirror.

  1. Install the screw.

  1. Install the inner rear view mirror cover.



14. INSTALL ROOF HEADLINING ASSEMBLY


    B076400E01
  1. Align the markings, and then install the wire harness with tape.

    NOTICE:
    Attach the roof wire harness securely.

  1. Install the silencer pads and headlining pad to the headlining.



    B073598E02
  1. Install the headlining with the 3 clips.



15. INSTALL MAP LIGHT ASSEMBLY
  1. Connect the map light connector.



    B076771E03
  1. Attach the 4 clips to install the map light.

  1. Install the 2 screws.



16. INSTALL ASSIST GRIP SUB-ASSEMBLY


    B076399E03
  1. Attach the 4 claws to install the assist grip.



17. INSTALL ASSIST GRIP COVER


    B076398E03
  1. Attach the 4 claws to install the 2 covers.



18. INSTALL VISOR HOLDER
  1. Install the visor holder and turn it clockwise.



19. INSTALL VISOR ASSEMBLY LH
  1. Connect the connector.



    B075287E01
  1. Install the visor with the 2 screws.



20. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



21. INSTALL FRONT PILLAR GARNISH LH


    B073594E03
  1. w/o Curtain Shield Airbag:
    Attach the 2 clips to install the pillar garnish.

  1. w/ Curtain Shield Airbag:
    Remove the protective cover.



  1. w/ Curtain Shield Airbag:
    Install the pillar garnish.



      B132621E01
    1. Set the claws of the pillar garnish to the area labeled C.

    2. Insert the tip of clip A into the pillar garnish's hole.

    3. Using needle-nose pliers, rotate the tip of clip A 90°. Then push the pillar garnish toward the vehicle body to attach the base of clip A and clip B.



22. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



23. INSTALL FRONT PILLAR GARNISH CORNER PIECE LH


    B136013E01
  1. Put protective tape as shown in the illustration.

    Standard measurement:
    Area
    Specified Condition
    A
    2.0 mm (0.079 in.)
    B
    10.0 mm (0.394 in.)
    C
    50.0 mm (1.969 in.)

  1. Attach the 5 claws to install the corner piece.



24. INSTALL FRONT PILLAR GARNISH CORNER PIECE RH

HINT:
Use the same procedures described for the LH side.



25. INSTALL FRONT DOOR OPENING TRIM LH


26. INSTALL FRONT DOOR OPENING TRIM RH


27. INSTALL COWL SIDE TRIM BOARD LH


    B073588E02
  1. Attach the claw and 2 clips to install the trim board.



28. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



29. REMOVE FRONT DOOR SCUFF PLATE LH


    B073586E02
  1. Attach the 8 claws and 2 clips to install the scuff plate.



30. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



31. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.



32. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


33. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.