Home › BODY › WINDSHIELD / WINDOWGLASS › WINDSHIELD GLASS

WINDSHIELD GLASS > REMOVAL

for Preparation Click here




1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



2. REMOVE FRONT DOOR SCUFF PLATE LH


    B073586E02
  1. Using a screwdriver, detach the 8 claws and 2 clips, and remove the scuff plate.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



4. REMOVE COWL SIDE TRIM BOARD LH


    B073588E02
  1. Using a screwdriver, detach the claw and 2 clips, and remove the trim board.

    HINT:
    Tape the screwdriver tip before use.



5. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



6. REMOVE FRONT DOOR OPENING TRIM LH
  1. Partially remove the front door opening trim weatherstrip LH so that the front pillar garnish LH can be removed .



7. REMOVE FRONT DOOR OPENING TRIM RH

HINT:
Use the same procedures described for the LH side.



8. REMOVE FRONT PILLAR GARNISH CORNER PIECE LH


    B132622E01
  1. Put protective tape as shown in the illustration.

    Standard measurement:
    Area
    Specified Condition
    A
    2.0 mm (0.079 in.)
    B
    10.0 mm (0.394 in.)
    C
    50.0 mm (1.969 in.)

  1. Using a screwdriver, detach the 5 claws and remove the corner piece.

    HINT:
    Tape the screwdriver tip before use.



9. REMOVE FRONT PILLAR GARNISH CORNER PIECE RH

HINT:
Use the same procedures described for the LH side.



10. REMOVE FRONT PILLAR GARNISH LH


    B073594E03
  1. w/o Curtain Shield Airbag:
    Using a screwdriver, detach the 2 clips and remove the pillar garnish.

    HINT:
    Tape the screwdriver tip before use.



  1. w/ Curtain Shield Airbag:
    Remove the pillar garnish.



      B079223E02
    1. Pull the pillar garnish so that clip B detaches, the base of clip A detaches, and the tip of clip A locks in the pillar garnish's hole.

    2. Using needle-nose pliers, rotate clip A 90°. Then pull the pillar garnish to release the tip of clip A from the pillar garnish.

    3. Pull the pillar garnish in the direction indicated by the arrow in the illustration to detach the claw.



    B076392E04
  1. w/ Curtain Shield Airbag:
    Protect the curtain shield airbag LH.

    1. Thoroughly cover the airbag with cloth or nylon that is approximately 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with double-sided tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with the protective cover as soon as the pillar garnish is removed.



11. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



12. REMOVE VISOR ASSEMBLY LH


    B075287E01
  1. Remove the 2 screws.

  1. Disconnect the connector and remove the visor.



13. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



14. REMOVE VISOR HOLDER


    B050596E01
  1. Remove the visor holder by turning it counterclockwise.



15. REMOVE ASSIST GRIP COVER


    B076398E04
  1. Using a screwdriver, detach the 4 claws and remove the 2 covers.

    HINT:
    Tape the screwdriver tip before use.



16. REMOVE ASSIST GRIP SUB-ASSEMBLY


    B076399E02
  1. Using a screwdriver, detach the 4 claws and remove the assist grip.

    HINT:
    Tape the screwdriver tip before use.



17. REMOVE MAP LIGHT ASSEMBLY


    B076771E02
  1. Remove the 2 screws.

  1. Using a moulding remover, detach the 4 clips and remove the map light.

  1. Disconnect the map light connector.



18. REMOVE ROOF HEADLINING ASSEMBLY

HINT:
It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining.

  1. Partially remove the roof headlining .



19. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)


B064964E02
  1. Push the cover in the direction indicated by the arrows labeled A and remove it.

  1. While holding down the claw in the direction indicated by the black arrow labeled B, slide the mirror in the direction indicated by the white arrow and remove it.



20. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)


B056435E02
  1. Remove the inner rear view mirror cover.

  1. Remove the screw.

  1. Slide the mirror in the direction indicated by the arrow in the illustration and remove the mirror.



21. REMOVE HOOD TO COWL TOP SEAL


    I038368E02
  1. Detach the 8 clips and remove the hood to cowl top seal.



22. REMOVE FRONT WIPER ARM HEAD CAP


23. REMOVE FRONT WIPER ARM LH
  1. Remove the 2 nuts and FR wiper arm LH.



24. REMOVE FRONT WIPER ARM RH
  1. Remove the nut and FR wiper arm RH.



25. REMOVE COWL TOP VENTILATOR LOUVER LH


    I038369E02
  1. Detach the 8 claws and clip, and remove the cowl top ventilator louver LH.



26. REMOVE COWL TOP VENTILATOR LOUVER RH


    I038370E02
  1. Detach the 8 claws and clip, and remove the cowl top ventilator louver RH.



27. REMOVE WINDSHIELD MOULDING OUTSIDE


B050448E03
  1. Using a knife, cut off the moulding as shown in the illustration.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Remove the remaining moulding.

    HINT:
    Make a partial cut in the moulding. Then pull and remove it by hand.



28. REMOVE WINDSHIELD GLASS


B063724E03
  1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.



    B073409E01
  1. From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.

  1. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

    NOTICE:
    1. When separating the glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.
    2. To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.



    B106095E03
  1. Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.

    HINT:
    Matchmarks do not need to be placed if not reusing the glass.

  1. Cut through the adhesive by pulling the piano wire around the glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.

  1. Disengage the stoppers.

  1. Using suction cups, remove the glass.



29. CLEAN WINDSHIELD GLASS


B106080
  1. Using a scraper, remove the damaged stoppers, dams and adhesive sticking to the glass.

  1. Clean the outer edges of the glass with white gasoline.

    NOTICE:
    Do not touch the glass surface after cleaning it.
    Even if using new glass, clean it with white gasoline.



30. CLEAN VEHICLE BODY


B106081E05
  1. Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      NOTICE:
      Be careful not to damage the vehicle body.

  1. Clean the contact surface of the vehicle body with cleaner.

    HINT:
    Even if all the adhesive has been removed, clean the vehicle body.