Home › RESTRAINTS › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY

REAR SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL REAR SEAT OUTER BELT ASSEMBLY CENTER
  1. Install the belt with the bolt on the retractor side.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the rear seatback cover RH .

  1. Install the rear seat headrest RH .

  1. Install the rear seat center headrest .

  1. Attach the 4 claws to install the cover .



    B076014E03
  1. Connect the floor anchor of the belt with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Make sure that the anchor part does not run onto the protruding part.



2. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH
  1. Install the belt on the retractor side with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Make sure that the anchor part does not run onto the protruding part of the side panel.

  1. Install the belt on the floor anchor side with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. With the belt installed, check that the belt locks when it is pulled out quickly.

    NOTICE:
    The check should be performed with the outer belt installed.

    If the operation is not as specified, replace the belt.



3. INSTALL ROOF SIDE GARNISH INNER RH

HINT:
Use the same procedures described for the LH side.



4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
  1. Install the deck trim side panel RH .

  1. Install the rear seat outer belt RH with the bolt on the floor anchor side.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



5. INSTALL REAR DECK TRIM COVER


    B076395E02
  1. Attach the 4 claws to install the trim cover.



6. INSTALL REAR DECK FLOOR BOX


7. INSTALL DECK FLOOR BOX LH


8. INSTALL REAR FLOOR NO. 4 BOARD


9. INSTALL REAR FLOOR NO. 1 BOARD


10. INSTALL REAR FLOOR NO. 2 BOARD


11. INSTALL TONNEAU COVER ASSEMBLY


12. INSTALL REAR SEAT BACK ASSEMBLY RH


    B076028E01
  1. Install the seatback with the 2 bolts.

    Torque:
    36.8 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Close the front part of the rear No. 1 floor deck board.

  1. Return the seatback to the upright position.

  1. Connect the rear seat outer belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



13. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


14. INSTALL REAR SIDE SEAT BACK FRAME RH


15. INSTALL REAR DOOR SCUFF PLATE RH


16. INSTALL REAR SEAT CUSHION ASSEMBLY

NOTICE:
When installing the seat cushion, make sure the seat belt buckle is not under the seat cushion.



    B132601E01
  1. Attach the seat cushion's rear hook to the center hinge.

  1. Insert the inner belts through the slits on the seat cushion.



    B132602
  1. Attach the seat cushion's 2 front hooks to the vehicle body.

  1. Confirm that the seat cushion is firmly installed.



17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


18. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.