Home › BODY › WINDSHIELD / WINDOWGLASS › BACK WINDOW FIX GLASS

BACK WINDOW FIX GLASS > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL BACK WINDOW GLASS SPACER
  1. Apply Primer G to the installation part of the spacers.

    HINT:
    If primer is applied to an area that is not specified, wipe off the primer with white gasoline before it dries.



    B073877E02
  1. Install 2 new spacers onto the glass as shown in the illustration.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



2. INSTALL BACK DOOR GLASS ADHESIVE DAM
  1. Apply Primer G to the glass where the adhesive dam will be installed.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Remove the peeling paper from the adhesive part of the dam. Install the dam (adhesive side) to the glass (Primer G area) as shown in the illustration.


    B073878E01



3. INSTALL BACK WINDOW MOULDING OUTSIDE



B076571E01

  1. Using a brush or sponge, apply Primer G to the contact surface of the back door glass.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.

    Standard measurement:
    Area
    Specified Condition
    a
    10.0 mm (0.394 in.)
    b
    9.0 mm (0.354 in.)



  1. Install the moulding as shown in the illustration.


    B076572E02

    Standard measurement:
    Area
    Specified Condition
    a
    0 mm (0 in.)
    b
    3.0 mm (0.118 in.)
    c
    1.5 mm (0.059 in.)
    d
    6.5 mm (0.256 in.)



4. INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY


    B067629E01
  1. Install the back door opener switch to the garnish with the 2 screws.



  1. Attach the 2 clips to install the garnish.


    B133842E01

  1. Install the 4 nuts.

  1. Connect the back door opener switch connector.



5. INSTALL BACK WINDOW FIX GLASS


B074628E03
  1. Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply primer to the adhesive.
    3. Throw away any leftover primer.
    4. Do not apply too much primer.



  1. Using a brush or sponge, apply Primer G to the contact surface of the back door glass.


    B073879E01

    HINT:
    If primer is applied to an area that is not specified, wipe off the primer with white gasoline before it dries.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Apply adhesive to the back door glass.


    B073880E01

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or Equivalent


    1. Cut off the tip of the cartridge nozzle as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.

    3. Apply adhesive to the back door glass as shown in the illustration.

      Standard measurement:
      Area
      Specified Condition
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)



  1. Install the back window fix glass to the vehicle body.

    1. Hold the back window glass in place securely with tape or equivalent until the adhesive has hardened.

      NOTICE:
      1. Check that the clips are attached to the vehicle body correctly.
      2. Check the clearance between the vehicle body and glass.

    2. Lightly press the front surface of the back door glass to ensure that the back door glass is securely fit to the vehicle body.



    3. BO03986E06
    4. Using a scraper, remove any excess or protruding adhesive.

      HINT:
      Apply adhesive onto the glass rim.

      NOTICE:
      Do not drive the vehicle within the time written in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



6. INSTALL REAR SPOILER SUB-ASSEMBLY


  1. Large Type:

    HINT:
    When installing the spoiler, heat the vehicle body and spoiler using a heat light.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)
    Spoiler
    20 to 30°C (68 to 86°F)

    NOTICE:
    Do not heat the vehicle body and rear spoiler excessively.


    1. Put protective tape under the rear spoiler.

    2. Using a heat light, heat the vehicle body surface and rear spoiler.

    3. Remove the double-sided tape from the vehicle body and rear spoiler.

    4. Wipe off any tape adhesive residue with cleaner.



    5. Apply new double-sided tape to the rear spoiler.


      B157869E01

    6. Using a heat light, heat the vehicle body and rear spoiler.

    7. Remove the release paper from the rear spoiler.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.

  1. Connect the center stop light connector.



    B157868E01
  1. Attach the 3 clips to install the rear spoiler.



    B157864
  1. Install the 4 bolts.



7. INSTALL BACK DOOR UPPER TRIM BOARD ASSEMBLY


B077067E03
  1. Attach the 5 clips to install the upper trim board.



8. INSTALL BACK DOOR LOWER TRIM BOARD ASSEMBLY


B075175E04
  1. Attach the 11 clips to install the lower trim board.



9. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.



10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


11. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.