Home › BODY › WINDSHIELD / WINDOWGLASS › BACK DOOR GLASS

BACK DOOR GLASS > REMOVAL

for Preparation Click here




1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



2. REMOVE REAR WIPER ARM ASSEMBLY (w/ Rear wiper)
  1. Remove the nut and rear wiper arm.



3. REMOVE BACK DOOR LOWER TRIM BOARD ASSEMBLY
  1. Using a screwdriver, detach the 11 clips and remove the lower trim board.

    HINT:
    Tape the screwdriver tip before use.



4. REMOVE BACK DOOR UPPER TRIM BOARD ASSEMBLY


    B077067E03
  1. Using a screwdriver, detach the 5 clips and remove the upper trim board.

    HINT:
    Tape the screwdriver tip before use.



5. REMOVE BACK DOOR TRIM UPPER PANEL ASSEMBLY


    B075176E03
  1. Using a screwdriver, detach the 5 clips and remove the trim panel.

    HINT:
    Tape the screwdriver tip before use.



6. REMOVE BACK DOOR SIDE GARNISH LH
  1. Using a screwdriver, detach the 3 clips and remove the garnish.

    HINT:
    Tape the screwdriver tip before use.



7. REMOVE BACK DOOR SIDE GARNISH RH
  1. Using a screwdriver, detach the 3 clips and remove the garnish.

    HINT:
    Tape the screwdriver tip before use.



8. REMOVE REAR WIPER MOTOR ASSEMBLY (w/ Rear wiper)


    I038386E01
  1. Disconnect the connector.

  1. Remove the 3 bolts and rear wiper motor.



9. REMOVE REAR SPOILER SUB-ASSEMBLY


    B157864E01
  1. Put protective tape under the rear spoiler.

  1. Remove the 4 bolts.



  1. Regular Type:



      B157880
    1. Using a screwdriver, detach the 3 clips.

      HINT:
      Tape the screwdriver tip before use.



  1. Large Type:



      B157878E01
    1. Using a screwdriver, detach the 3 clips and peel off the double-sided tape.

      HINT:
      Tape the screwdriver tip before use.

  1. Disconnect the center stop light connector and remove the rear spoiler.



10. REMOVE BACK DOOR GLASS


B073869E01
  1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.

    NOTICE:
    When separating the back door glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.



    B073870E01
  1. From the interior, insert a piano wire between the vehicle body and back door glass as shown in the illustration.

  1. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

  1. Cut through the adhesive by pulling the piano wire around the back door glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when removing the back door glass.

  1. Using suction cups, remove the back door glass.



11. CLEAN BACK DOOR GLASS


BO04421E02
  1. Clean the outer edge of the back door glass with white gasoline.

    NOTICE:
    1. Do not touch the back door glass surface after cleaning it.
    2. Be careful not to damage the glass.
    3. Even if using new back door glass, clean the back door glass with white gasoline.



12. CLEAN VEHICLE BODY


B106081E02
  1. Using a scraper, remove the moulding and adhesive from the back door glass.

  1. Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      NOTICE:
      Be careful not to damage the vehicle body.

    2. Clean the contact surface of the vehicle body with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.