Home › BODY › WINDSHIELD / WINDOWGLASS › QUARTER WINDOW GLASS

QUARTER WINDOW GLASS > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL QUARTER WINDOW ASSEMBLY LH


B073866E01
  1. Using a brush or sponge, apply primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer coating to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Using a brush or sponge, apply primer G to the contact surface of the glass.


    B073867E01

    HINT:
    If primer is applied to an area that is specified, wipe off the primer with white gasoline before it dries.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Apply adhesive to the quarter window glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or Equivalent




    1. Cut off the tip of the cartridge nozzle as shown in the illustration.


      B073868E03

      Standard measurement:
      Area
      Specified Condition
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.

    3. Apply adhesive to the quarter window glass as shown in the illustration.



  1. Install the quarter window glass to the vehicle body.

    1. Hold the quarter window glass in place securely with protective tape or equivalent until the adhesive hardens.

      NOTICE:
      1. Allow the primer coating to dry for 3 minutes or more.
      2. Check that the clips are attached to the body correctly.
      3. Check the clearance between the body and glass.

    2. Lightly press the front surface of the glass to ensure a close fit.



    3. BO03986E05
    4. Using a scraper, remove any excess or protruding adhesive.

      HINT:
      Apply adhesive onto the glass rim.

      NOTICE:
      Do not drive the vehicle within the time written in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



2. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH


    B073592E03
  1. Attach the 6 clips and claw to install the inner garnish.



3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    B073591E02
  1. Attach the 7 claws and 3 clips to install the side panel.

  1. Install the clip, screw and 2 bolts.



4. INSTALL REAR DECK TRIM COVER


    B076395E02
  1. Attach the 4 claws to install the trim cover.



5. INSTALL REAR NO. 1 FLOOR BOARD


    B132619E01
  1. Attach the 5 clips to install the floor board.

  1. Install the 2 clips, 2 bolts and 2 rope hooks.



6. INSTALL DECK FLOOR BOX LH


7. INSTALL REAR DECK FLOOR BOX


8. INSTALL REAR NO. 4 FLOOR BOARD


9. INSTALL REAR NO. 3 FLOOR BOARD


10. INSTALL REAR NO. 2 FLOOR BOARD


11. INSTALL TONNEAU COVER ASSEMBLY


12. INSTALL BACK DOOR WEATHERSTRIP


13. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


14. INSTALL REAR SIDE SEATBACK FRAME LH


    B132620
  1. Attach the claw to install the frame.

  1. Install the bolt.



15. INSTALL REAR SEAT CUSHION ASSEMBLY

NOTICE:
When installing the seat cushion, make sure the seat belt buckle is not under the seat cushion.



    B132601E01
  1. Attach the seat cushion's rear hook to the center hinge.

  1. Insert the inner belts through the slits on the seat cushion.



    B132602
  1. Attach the seat cushion's 2 front hooks to the vehicle body.

  1. Confirm that the seat cushion is firmly installed.



16. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.