Home › ENGINE › 1NZ-FXE ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > REPLACEMENT

for Preparation Click here



1. REPLACE INTAKE VALVE GUIDE BUSH


    A001067E01
  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).



    A037110E01
  1. Using SST and a hammer, tap out the guide bush.

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)



    A001445E01
  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Standard bore diameter:
    Bush size
    Specified Condition
    STD
    9.685 to 9.706 mm (0.3813 to 0.3821 in.)
    O/S 0.05
    9.735 to 9.756 mm (0.3833 to 0.3841 in.)

    If the bush bore diameter of the cylinder head is greater than 9.706 mm (0.3821 in.), machine the bush bore to a dimension of 9.735 to 9.755 mm (0.3833 to 0.3841 in.).
    If the bush bore diameter of the cylinder head is greater than 9.756 mm (0.3841 in.), replace the cylinder head.

  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).



    A080977E02
  1. Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Standard protrusion height:
    9.0 to 9.4 mm (0.354 to 0.370 in.)



    A001447E01
  1. Using a sharp 5 mm reamer, ream the guide bush to obtain the standard specified clearance between the guide bush and the valve stem.

    Standard oil clearance:
    0.025 to 0.060 mm (0.0010 to 0.0024 in.)



2. REPLACE EXHAUST VALVE GUIDE BUSH
  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Using SST and a hammer, tap out the guide bush.

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Standard bore diameter:
    Bush size
    Specified Condition
    STD
    9.685 to 9.706 mm (0.3813 to 0.3821 in.)
    O/S 0.05
    9.735 to 9.756 mm (0.3833 to 0.3841 in.)

    If the bush bore diameter of the cylinder head is greater than 9.706 mm (0.3821 in.), machine the bush bore to a dimension of 9.735 to 9.755 mm (0.3833 to 0.3841 in.).
    If the bush bore diameter of the cylinder head is greater than 9.756 mm (0.3841 in.), replace the cylinder head.

  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Standard protrusion height:
    9.0 to 9.4 mm (0.354 to 0.370 in.)

  1. Using a sharp 5 mm reamer, ream the guide bush to obtain the standard specified clearance between the guide bush and valve stem.

    Standard oil clearance:
    0.030 to 0.065 mm (0.0012 to 0.0026 in.)