Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1794    Open in Occupant Classification ECU Battery Positive Line

for Preparation Click here


DESCRIPTION

DTC B1794 is set when a malfunction is detected in the occupant classification ECU battery positive line.

DTC No.
DTC Detection Condition
Trouble Area
B1794
When one of following conditions is met:
  1. Occupant classification ECU circuit malfunction
  2. Occupant classification ECU malfunction
  3. Occupant classification ECU detects short to ground signal in passenger side buckle switch circuit for 2 seconds
  1. Wire harness
  2. Occupant classification ECU

WIRING DIAGRAM


C130828E02


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Turn the power switch ON (IG).

  1. Clear the DTCs (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

  1. Turn the power switch OFF, and wait for at least 10 seconds.

  1. Turn the power switch ON (IG).

  1. Check the DTCs (Click here).

    OK:
    DTC B1794 is not output.

    HINT:
    DTCs other than B1794 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECTION OF CONNECTOR
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTOR
OK


3.CHECK WIRE HARNESS (SOURCE VOLTAGE)


    H043112E15
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the O4 connector from the occupant classification ECU.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O4-1 (+B) - Body ground
    Always
    10 to 14 V
    O4-7 (IG) - Body ground
    Power switch ON (IG)
    10 to 14 V

  1. Turn the power switch OFF.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    O4-3 (GND) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR (BATTERY - OCCUPANT CLASSIFICATION ECU)
OK


4.CHECK FOR DTC
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Connect the connectors to the occupant classification ECU.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Clear the DTCs (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

  1. Turn the power switch OFF, and wait for at least 10 seconds.

  1. Turn the power switch ON (IG).

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1794 is not output.

    HINT:
    DTCs other than B1794 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


5.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU.


NEXT


6.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed


NEXT


7.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END