Home › BODY › SEAT › FRONT SEAT ASSEMBLY

FRONT SEAT ASSEMBLY > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.

CAUTION:
Wear protective gloves. Sharp surfaces on the seat adjuster may injure your hands.



1. INSTALL OCCUPANT DETECTION ECU (for Front Passenger Side)


2. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)


H043795E03
  1. Check that the power switch is off.

  1. Check that the negative battery (-) terminal is disconnected.

    CAUTION:
    After disconnecting the cable from the negative battery terminal, wait for at least 90 seconds before starting the operation.

  1. Using a 1 mm (0.039 in.) feeler gauge, install the seat position sensor.

    NOTICE:
    1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
    2. When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    HINT:
    Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.023 in.) to 1.4 mm (0.055 in.).

  1. Using a "torx" socket wrench (T30), tighten the "torx" screw to install the seat position sensor.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.023 in.) to 1.4 mm (0.055 in.).

  1. Check that there is no looseness in the installation parts of the seat position sensor.

  1. Connect the connector.

  1. Install the seat slide position sensor protector to the seat position sensor.



3. INSTALL FRONT SEAT CUSHION LOWER SHIELD LH
  1. Attach the claw to install the lower shield.



4. INSTALL FRONT SEAT CUSHION LOWER SHIELD RH
  1. Attach the claw to install the lower shield.



5. INSTALL RECLINING ADJUSTER UPPER INSIDE COVER LH
  1. Install the inside cover with the screw.



6. INSTALL RECLINING ADJUSTER UPPER INSIDE COVER RH
  1. Install the inside cover with the screw.



7. INSTALL RECLINING ADJUSTER LOWER INSIDE COVER LH
  1. Install the inside cover with the screw.



8. INSTALL RECLINING ADJUSTER LOWER INSIDE COVER RH
  1. Install the inside cover with the screw.



9. INSTALL FRONT SEATBACK COVER

NOTICE:

  1. B050126E09
  2. Be careful not to damage the cover.
  3. When installing the hog rings, avoid wrinkling the cover.



    B132589E01
  1. Using hog ring pliers, install the seatback cover to the seatback pad with 4 new hog rings.

  1. Install the seatback cover (with pad) to the seat adjuster.



    B060977E01
  1. Attach the 4 claws to install the 2 headrest supports.



    B087721E01
  1. w/ Front Seat Side Airbag:
    Fully cover the airbag with the 2 seatback cover brackets and install the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with side airbags, the seatback cover must be securely installed. If not, the side airbag may not deploy properly.
    2. Make sure that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.



    B132588E01
  1. Attach the 2 hooks to the seat adjuster.



    B077035E01
  1. Using hog ring pliers, attach a rubber with 3 new hog rings.



    B076023E01
  1. Using hog ring pliers, install 3 new hog rings.



10. INSTALL FRONT SEAT CUSHION COVER

NOTICE:

  1. B050126E09
  2. Be careful not to damage the cover.
  3. When installing the hog rings, avoid wrinkling the cover.



    B132587E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 6 new hog rings.

  1. Using hog ring pliers, install the seat cushion cover (with pad) to the seat adjuster with 2 new hog rings and hooks.



11. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH
  1. Install the inner belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



12. INSTALL FRONT SEAT CUSHION INNER SHIELD LH


    B076921E02
  1. Attach the claw and clip to install the seat cushion inner shield.

  1. Install the screw.



13. INSTALL FRONT SEAT CUSHION SHIELD LH


    B132590E01
  1. Attach the 2 claws and clip to install the seat cushion shield.

  1. Install the screw.



    B132585
  1. Attach the 2 rubber bands of back of the front seatback cover.



14. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
  1. Attach the claw to install the release handle.