Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0101    Mass Air Flow Circuit Range / Performance Problem

for Preparation Click here


DESCRIPTION

Refer to DTC P0102 .

DTC No.
DTC Detection Conditions
Trouble Areas
P0101
Conditions (a), (b), (c), (d) and (e) continue for more than 10 seconds (2 trip detection logic):
(a) Engine running
(b) Engine coolant temperature 70°C (158°F) or higher
(c) Throttle Position (TP) sensor voltage 0.24 to 2 V
(d) Average engine load value ratio less than 0.85, or more than 1.15 (varies with estimated engine load)
Average engine load value ratio = Average engine load based on mass air flow meter output / Average engine load estimated from driving conditions
(e) Average air-fuel ratio less than -20%, or more than 20%
  1. Mass Air Flow (MAF) meter
  2. Air induction system
  3. PCV hose connections

MONITOR DESCRIPTION

The MAF (Mass Air Flow) meter is a sensor that helps the ECM calculate the amount of air flowing through the throttle valve. The ECM uses this information to determine the fuel injection time and provide a proper air-fuel ratio. Inside the MAF meter, there is a heated platinum wire exposed to the flow of intake air. By applying a specific current to the wire, the ECM heats this wire to a given temperature. The flow of incoming air cools the wire and an internal thermistor, changing their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the MAF meter. The voltage level is proportional to the air flow through the sensor and the ECM interprets this voltage as the intake air amount. If there is a defect in the sensor or an open or short circuit, the voltage level will deviate from the normal operating range. The ECM interprets this deviation as a defect in the MAF meter and sets a DTC.
Example:
If the MAF meter voltage is higher than 2.2 V when the engine is idling, the ECM sets P0101 (2 trip detection logic). If the MAF meter voltage is higher than 0.7 V when the throttle valve is opened, the ECM sets P0101 (2 trip detection logic).

MONITOR STRATEGY


Related DTCs
P0101: Mass air flow meter rationality
Required sensors/components
Main sensors:
Mass air flow meter
Related sensors:
Engine speed sensor, engine coolant temperature sensor, throttle position sensor
Frequency of operation
Continuous
Duration
10 times
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
P0115 - P0118 (ECT sensor)
P0120 - P0223, P2135 (TP sensor)
P0125 (Insufficient ECT for closed loop)
P0335 (CKP sensor)
P0340, P0341 (CMP sensor)
Throttle position
0.2 to 2 V
Battery voltage
10.5 V or more
Engine coolant temperature
70°C (158°F) or more
IAT sensor circuit
OK
ECT sensor circuit
OK
CKP sensor circuit
OK
TP sensor circuit
OK
EVAP leak detection pump
OK
EVAP vent valve
OK

TYPICAL MALFUNCTION THRESHOLDS


Case1: Mass air flow meter rationality (High voltage) 
Mass air flow meter voltage
More than 1.34 V (varies with throttle position)

Case2: Mass air flow meter rationality (Low voltage) 
Mass air flow meter voltage
Less than 0.85 V (varies with throttle position)

WIRING DIAGRAM

Refer to DTC P0100 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0101)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0101
    A
    P0101 and other DTCs
    B

HINT:
If any DTCs other than P0101 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leaks.

    OK:
    No leaks in air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


3.CHECK PCV HOSE (HOSE CONNECTION)

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK

REPLACE MASS AIR FLOW METER