Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0125    Insufficient Coolant Temperature for Closed Loop Fuel Control

for Preparation Click here


DESCRIPTION

Refer to DTC P0115 .

DTC No.
DTC Detection Condition
Trouble Area
P0125
Engine coolant temperature hardly changes for 58 seconds after engine start
(2 trip detection logic)
  1. Cooling system
  2. Engine coolant temperature sensor
  3. Thermostat
P0125
Engine coolant temperature hardly changes for 109 seconds after engine start
(2 trip detection logic)
  1. Cooling system
  2. Engine coolant temperature sensor
  3. Thermostat
P0125
Engine coolant temperature hardly changes for 20 minutes after engine start
(2 trip detection logic)
  1. Cooling system
  2. Engine coolant temperature sensor
  3. Thermostat

HINT:
ECT represents engine coolant temperature, and IAT represents intake air temperature.


MONITOR DESCRIPTION

The engine coolant temperature (ECT) sensor is used to monitor the temperature of the engine coolant. The resistance of the sensor varies with the actual engine coolant temperature. The ECM applies voltage to the sensor and the varying resistance of the sensor causes the signal voltage to vary. The ECM monitors the ECT signal voltage after engine start-up. If, after sufficient time has passed, the sensor still reports that the engine is not warm enough for closed-loop fuel control, the ECM interprets this as a fault in the sensor or cooling system and sets a DTC.
Example:
The engine coolant temperature was 0°C (32°F) at engine start. After driving 5 minutes, the ECT sensor still indicates that the engine is not warm enough to begin the air-fuel ratio feedback control. The ECM interprets this as a fault in the sensor or cooling system and will set a DTC.

MONITOR STRATEGY


Related DTCs
P0125
Required sensors/components (Main)
Engine coolant temperature sensor, cooling system, thermostat
Required sensors/components (Related)
Cooling system, thermostat
Frequency of operation
Once per driving cycle
Duration
58 seconds (Case 1)
109 seconds (Case 2)
1,200 seconds (Case 3)
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Case 1 
Monitor will run whenever these DTCs are not present
P0100 - P0103 (MAF meter)
P0110 - P0113 (IAT sensor)
P0115 - P0118 (ECT sensor)
Engine coolant or intake air temperature at engine start
-8.34°C (17°F) or more

Case 2 
Monitor will run whenever these DTCs are not present
P0100 - P0103 (MAF meter)
P0110 - P0113 (IAT sensor)
P0115 - P0118 (ECT sensor)
Engine coolant or intake air temperature at engine start
Between -19.45°C (-3°F) and -8.34°C (17°F)

Case 3 
Monitor will run whenever these DTCs are not present
P0100 - P0103 (MAF meter)
P0110 - P0113 (IAT sensor)
P0115 - P0118 (ECT sensor)
Engine coolant or intake air temperature at engine start
Lower than -19.45°C (-3°F)

TYPICAL MALFUNCTION THRESHOLDS


Engine coolant temperature
Less than 10°C (50°F)

WIRING DIAGRAM

Refer to DTC P0115 .

INSPECTION PROCEDURE

HINT:
  1. If DTCs P0115, P0116, P0117, P0118 and P0125 are output simultaneously, engine coolant temperature sensor circuit may be open or shorted. Perform troubleshooting on DTC P0115, P0117 or P0118 first.
  2. Read freeze frame data using Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0125)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Turn Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs using Techstream.

    Result:
    Display (DTC output)
    Proceed to
    P0125
    A
    P0125 and other DTCs
    B

    HINT:
    If any other codes besides P0125 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.INSPECT THERMOSTAT
  1. Check the valve opening temperature of the thermostat.

    OK:
    Thermostat valve begins to open at temperature of 80 to 84°C (176 to 183°F)

    HINT:
    Also check that the valve is completely closed at a temperature lower than specified above.



NG
REPLACE THERMOSTAT
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR