Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0505    Idle Control System Malfunction

for Preparation Click here


MONITOR DESCRIPTION

The idle speed is controlled by the Electronic Throttle Control System (ETCS).
The ETCS is composed of the throttle motor which operates the throttle valve, and the throttle position sensor which detects the opening angle of the throttle valve.
The ECM controls the throttle motor to provide the proper throttle valve opening angle to obtain the target idle speed.
The ECM regulates the idle speed by opening and closing the throttle valve using the ETCS. If the actual idle RPM varies more than a specified amount or a learned value of the idle speed control remains at the maximum or minimum five times or more during a trip, the ECM concludes that there is a problem in the idle speed control ECM function. The ECM will turn on the MIL and a DTC will be set.
Example:
If the actual idle RPM varies from the target idle RPM by more than 200 (*1) rpm five times during a drive cycle, the ECM will turn on the MIL and a DTC will be set.

HINT:
*1: RPM threshold varies depending on engine loads.


A082389E21


DTC No.
DTC Detection Condition
Trouble Area
P0505
Idle speed continues to vary greatly from target speed
(1 trip detection logic)
  1. Electronic throttle control system
  2. Air induction system
  3. PCV valve and hose
  4. ECM

MONITOR STRATEGY


Related DTCs
P0505: Idle air control malfunction (Functional check)
Required sensors/components
Main:
Crankshaft position sensor
Related:
Vehicle speed sensor, engine coolant temperature sensor
Frequency of operation
Once per driving cycle
Duration
10 minutes
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
None
Engine
Running

TYPICAL MALFUNCTION THRESHOLDS


Either of the following conditions is met:
1 or 2
1. Frequency that both of the following conditions (a) and (b) are met:
5 times or more
(a) Engine rpm-Target rpm
Less than -100 rpm, or more than 150 rpm
(b) Vehicle condition
Stop after vehicle was driven by 6.25 mph (10 km/h) or more
2. Frequency that both of the following conditions (c) and (d) are met:
Once
(c) Engine rpm-Target rpm
Less than -100 rpm, or more than 150 rpm
(d) IAC flow rate learning value
0.6 L/sec. or less, 4.5 L/sec. or more

INSPECTION PROCEDURE

HINT:
Read freeze frame data using Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0505)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Turn Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:
    Display (DTC output)
    Proceed to
    P0505
    A
    P0505 and other DTCs
    B

    HINT:
    If any other codes besides P0505 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.CHECK CONNECTION OF PCV HOSE

OK:
PCV hose is connected correctly and has no damage.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.CHECK AIR INDUCTION SYSTEM
  1. Check for vacuum leaks in the air induction system.

    OK:
    No leakage in the air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK

CHECK ELECTRIC THROTTLE CONTROL SYSTEM