Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

HYBRID CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

NOTICE:
  1. The value of the DATA LIST may vary significantly if there are slight differences in measurement, differences in the environment in which the measurements are obtained, or the aging of the vehicle. Thus, definite standards or judgment values are unavailable. Therefore, there may be a malfunction even if a measured value is within the reference range.
  2. In the event of intricate symptoms, collect sample data from another vehicle of the same model operating under identical conditions, in order to reach an overall judgment by comparing all the items of DATA LIST.

HINT:
Using the DATA LIST displayed on the Techstream, you can read values including those of the switches, sensors, actuators, without removing any parts . Reading the DATA LIST as the first step of troubleshooting is one method to shorten diagnostic time.

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch ON (IG).

  3. Enter the following menus: Powertrain / Hybrid Control / Data List.

  4. Check the results by referring to the following table.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Coolant Temp
    Engine coolant temperature /
    Min.: -40°F (-40°C), Max.: 284°F (140°C)
    After warming up:
    176 to 212°F (80 to 100°C)
    1. The value is -40°F (-40°C):
      Open in sensor circuit
    2. If the value is 284°F (140°C):
      Short in sensor circuit
    Engine Revolution
    Min.: 0, Max.: 16383.75
    Idling: 950 to 1050 rpm
    -
    Vehicle Spd
    Vehicle speed /
    Min.: 0 mph (0 km/h), Max.: 158.45 mph (255 km/h)
    Vehicle stopped: 0 mph (0 km/h)
    -
    Engine Run Time
    Elapsed time after starting engine /
    Min.: 0 s, Max.: 65,535 s
    -
    -
    +B
    Auxiliary battery voltage /
    Min.: 0 V, Max.: 65.535 V
    Constant:
    Auxiliary battery voltage +-3 V
    -
    Accel Pedal Pos #1
    No. 1 accelerator pedal position sensor /
    Min.: 0%, Max.: 100%
    Accelerator pedal depressed:
    Changes with accelerator pedal pressure
    -
    Accel Pedal Pos #2
    No. 2 accelerator pedal position sensor /
    Min.: 0%, Max.: 100%
    Accelerator pedal depressed:
    Changes with accelerator pedal pressure
    -
    Ambient Temperature
    Ambient air temperature /
    Min.: -40°F (-40°C), Max.: 419°F (215°C)
    Power switch ON (IG):
    Same as ambient air temperature
    -
    Intake Air Temperature
    Intake air temperature /
    Min.: -40°F (-40°C), Max.: 284°F (140°C)
    Constant:
    Same as ambient air temperature
    -
    DTC Clear Warm Up
    The number of times engine is warmed up after clearing DTCs /
    Min.: 0, Max.: 255
    MIL OFF, engine coolant temperature increases from below 72°F (22°C) before starting the engine to above 158°F (70°C) after starting the engine:
    Increases once
    -
    DTC Clear Run Distance
    Drive distance after clearing DTCs /
    Min.: 0 km, Max.: 65,535 km
    -
    -
    DTC Clear Min
    Elapsed time after clearing DTCs /
    Min.: 0 min, Max.: 65,535 min
    -
    -
    MIL on Run Distance
    Drive distance after malfunction occurrence /
    Min.: 0 km, Max.: 65,535 km
    -
    -
    MIL on Engine Run Time
    Elapsed time after starting engine with MIL ON /
    Min.: 0 min, Max.: 65,535 min
    -
    -
    MIL Status
    MIL status / ON or OFF
    MIL ON: ON
    Constant ON:
    Repair in accordance with detected DTCs
    Model Code
    Model code
    NHW
    -
    Engine Code
    Engine code
    1NZFXE
    -
    ECU Code
    ECU code
    47211
    -
    Destination
    Destination
    A
    -
    Motor (MG2) Revolution
    MG2 revolution /
    Min.: -16,383 rpm, Max.: 16,383 rpm
    -
    -
    Motor (MG2) Torq
    MG2 torque /
    Min.: -500 Nm, Max.: 500 Nm
    -
    -
    M (MG2) Trq Exec Val
    MG2 torque execution value /
    Min.: -512 Nm, Max.: 508 Nm
    After full-load acceleration with READY light ON and engine stopped:
    Less than +-20% of MG2 TORQ
    -
    Generator (MG1) Rev
    MG1 revolution /
    Min.: -16,383 rpm, Max.: 16,383 rpm
    -
    -
    Generator (MG1) Torq
    MG1 torque /
    Min.: -500 Nm, Max.: 500 Nm
    -
    -
    G (MG1) Trq Exec Val
    MG1 torque execution value /
    Min.: -512 Nm, Max.: 508 Nm
    1 second has elapsed after the engine was started automatically with READY light ON, engine stopped, A/C fan Hi, headlight ON and the P position:
    Less than +-20% of MG1 TORQ
    -
    Regenerative Brake Torq
    Regenerative brake execution torque /
    Min.: 0 Nm, Max.: 186 Nm
    -
    -
    Rqst Regen Brake Torq
    Regenerative brake request torque /
    Min.: 0 Nm, Max.: 186 Nm
    Vehicle speed 19 mph (30 km/h) and master cylinder hydraulic pressure -200 Nm:
    Changes with brake pedal pressure
    -
    Inverter Temp - (MG1)
    MG1 inverter temperature /
    Min.: -58°F (-50°C), Max.: 401°F (205°C)
    1. Undisturbed for 1 day at 77°F (25°C): 77°F (25°C)
    2. Street driving:
      77 to 176°F (25 to 80°C)
    1. If the value is -58°F (-50°C):
      +B short in sensor circuit
    2. If the value is 401°F (205°C):
      Open or GND short in sensor circuit
    Inverter Temp - (MG2)
    MG2 inverter temperature /
    Min.: -58°F (-50°C), Max.: 401°F (205°C)
    1. Undisturbed for 1 day at 77°F (25°C): 77°F (25°C)
    2. Street driving:
      77 to 176°F (25 to 80°C)
    1. If the value is -58°F (-50°C):
      +B short in sensor circuit
    2. If the value is 401°F (205°C):
      Open or GND short in sensor circuit
    Motor Temp No2
    Transaxle fluid temperature /
    Min.: -58°F (-50°C), Max.: 401°F (205°C)
    1. Undisturbed for 1 day at 77°F (25°C): 77°F (25°C)
    2. Street driving:
      77 to 176°F (25 to 80°C)
    1. If the value is -58°F (-50°C):
      Open or +B short in sensor circuit
    2. If the value is 401°F (205°C):
      GND short in sensor circuit
    Motor Temp No1
    MG2 motor temperature /
    Min.: -58°F (-50°C), Max.: 401°F (205°C)
    1. Undisturbed for 1 day at 77°F (25°C): 77°F (25°C)
    2. Street driving:
      77 to 176°F (5 to 80°C)
    1. If the value is -58°F (50°C):
      Open or +B short in sensor circuit
    2. If the value is 401°F (205°C):
      GND short in sensor circuit
    Converter Temperature
    Boost converter temperature /
    Min.: -58°F (-50°C), Max.: 401°F (205°C)
    1. Undisturbed for 1 day at 77°F (25°C): 77°F (25°C)
    2. Street driving:
      77 to 140°F (25 to 60°C)
    1. If the value is -58°F (-50°C):
      +B short in sensor circuit
    2. If the value is 401°F (205°C):
      Open or GND short in sensor circuit
    Accelerator Degree
    Accelerator pedal depressed angle /
    Min.: 0%, Max.: 100%
    Accelerator pedal depressed:
    Changes with accelerator pedal pressure
    -
    Request Power
    Engine power output request value /
    Min.: 0 W, Max.: 320,000 W
    -
    -
    Target Engine Rev
    Target engine speed /
    Min.: 0 rpm, Max.: 8,000 rpm
    -
    -
    Engine Spd
    Engine speed /
    Min.: 0 rpm, Max.: 8,000 rpm
    Idling*: 950 to 1,050 rpm
    -
    Vehicle Speed (Resolver)
    Resolver vehicle speed /
    Min.: -159.07 mph (-256 km/h), Max.: 157.83 mph (254 km/h)
    Driving at 25 mph (40 km/h):
    25 mph (40 km/h)
    -
    Master Cylinder Ctrl Trq
    Braking torque that is equivalent to the master cylinder hydraulic pressure /
    Min.: -512 Nm, Max.: 508 Nm
    Brake pedal depressed:
    Changes with brake pedal pressure
    -
    State of Charge
    Battery state of charge /
    Min.: 0%, Max.: 100%
    Constant: 0 to 100%
    -
    WOUT Control Power
    Discharge control power value /
    Min.: 0 W, Max.: 81,600 W
    21,000 W or less
    -
    WIN Control Power
    Charge control power value /
    Min.: -40,800 W, Max.: 0 W
    -25,000 W or more
    -
    Discharge Rqst to SOC
    Discharge request to adjust SOC /
    Min.: -20,480 W, Max.: 20,320 W
    1. Uniform on-board charging: -4,400 W
    2. Usually: 0 W
    -
    Power Resource VB
    HV battery voltage /
    Min.: 0 V, Max.: 510 V
    READY light ON and P position:
    150 to 300 V
    -
    Power Resource IB
    HV battery current /
    Min.: -256 A, Max.: 254 A
    -
    -
    VL-Voltage before Boosting
    High voltage before it is boosted /
    Min.: 0 V, Max.: 510 V
    Power switch ON (READY):
    Practically the same as the HV battery voltage
    1. If the value is 0 V:
      Open or GND short in sensor circuit
    2. If the value is 510 V:
      +B short in sensor circuit
    VH-Voltage after Boosting
    High voltage after it is boosted /
    Min.: 0 V, Max.: 765 V
    Engine revved up in P position:
    HV battery voltage to 500 V
    1. If the value is 0 V:
      Open or GND short in sensor circuit
    2. If the value is 765 V:
      +B short in sensor circuit
    Boost Ratio
    Boost ratio /
    Min.: 0%, Max.: 100%
    The pre-boost voltage and the post-boost voltage are equal:
    0 to 10%
    -
    Drive Condition ID
    Drive condition ID /
    Min.: 0, Max.: 6
    1. Engine stopped: 0
    2. Engine about to be stopped: 1
    3. Engine about to be started: 2
    4. Engine operated or operating: 3
    5. Generating or loading movement: 4
    6. Revving up with P position: 6
    -
    Shift Sensor Main
    Output voltage of the shift position sensor (main) /
    Min.: 0 V, Max.: 5 V
    1. Selector lever in home position:
      2.0 to 3.0 V
    2. Shifting into R position:
      4.0 to 4.8 V
    3. Shifting into B or D position:
      0.2 to 1.0 V
    -
    Shift Sensor Sub
    Output voltage of the shift position sensor (sub) /
    Min.: 0 V, Max.: 5 V
    1. Selector lever in home position:
      2.0 to 3.0 V
    2. Shifting into R position:
      4.0 to 4.8 V
    3. Shifting into B or D position:
      0.2 to 1.0 V
    -
    Shift Sensor Select Main
    Output voltage of the select position sensor (main) /
    Min.: 0 V, Max.: 5 V
    1. Selector lever in home position:
      0.5 to 2.0 V
    2. Shifting into R, N or D position:
      3.0 to 4.85 V
    -
    Shift Sensor Select Sub
    Output voltage of the select position sensor (sub) /
    Min.: 0 V, Max.: 5 V
    1. Selector lever in home position:
      0.5 to 2.0 V
    2. Shifting into R, N or D position:
      3.0 to 4.85 V
    -
    Shift Sensor Shift Pos
    Shift position
    P, R, N, D or B
    -
    Crank Position
    Min.: -90, Max.: 90
    -
    -
    A/C Consumption Pwr
    A/C consumption power /
    Min.: 0 kW, Max.: 5 kW
    -
    -
    Loading Condition
    Loading condition
    1. MG1 load: MG1
    2. MG2 load: MG2
    -
    Short Wave Highest Val
    Waveform voltage in leak detection circuit in battery ECU /
    Min.: 0 V, Max.: 5 V
    READY light is left ON for 2 minutes, and the pre-boost voltage and the post-boost voltage are equal:
    4 V or more
    -
    Type of ECU
    Type of ECU
    HV ECU
    -
    Num of Current Code
    The number of current DTCs /
    Min.: 0, Max.: 255
    -
    -
    Num of History Code
    The number of history DTCs /
    Min.: 0, Max.: 255
    -
    -
    Check Mode
    Check mode /
    ON or OFF
    -
    -
    Calculate Load
    Min.: 0%, Max.: 100%
    1. Idling (Inspection Mode): 11 to 22%
    2. Driving (2,500 rpm): 12 to 18.2%
    -
    Throttle Position
    Min.: 0%, Max.: 100%
    1. Throttle valve fully closed: 10 to 24%
    2. Throttle valve fully open: 64 to 96%
    -
    Engine Stop Request
    Engine stop request /
    NO or RQST
    Requesting engine stop:
    RQST
    -
    Engine Idling Request
    Engine idling request /
    NO or RQST
    Requesting idle:
    RQST
    -
    Main Batt Charging Rqst
    HV battery charging request /
    NO or RQST
    Requesting HV battery charging:
    RQST
    -
    HCAC OBD Request
    0: NO, 1: RQST


    Aircon Request
    Engine starting request from air conditioning amplifier /
    NO or RQST
    Requesting engine start from air conditioning amplifier:
    RQST
    -
    Engine Warming Up Rqst
    Engine warm-up request /
    NO or RQST
    Requesting engine warm-up:
    RQST
    -
    System Main Relay Status - (SMRP)
    Operating condition of No. 1 system main relay /
    ON or OFF
    Power switch ON (READY):
    OFF
    -
    System Main Relay Status - SMRB
    Operating condition of No. 2 system main relay /
    ON or OFF
    Power switch ON (READY):
    ON
    -
    System Main Relay Status - SMRG
    Operating condition of No. 3 system main relay /
    ON or OFF
    Power switch ON (READY):
    ON
    -
    MG1 Gate Status
    MG1 gate status /
    ON or OFF
    ON
    -
    MG2 Gate Status
    MG2 gate status /
    ON or OFF
    Shutting down motor inverter:
    ON
    -
    Converter Gate Status
    Boost converter gate status /
    ON or OFF
    Shutting down boost converter:
    ON
    -
    Aircon Gate Status
    A/C gate status /
    ON or OFF
    Shutting down A/C inverter:
    ON
    -
    Smart Key Status
    Electronic key ID code check status /
    ON or OFF
    When electronic key ID code corresponds to ID code registered in ECU:
    ON
    -
    Converter Carrier Freq
    Converter signal carrier frequency / 5 kHz / 10kHz
    5 kHz / 10kHz
    -

    HINT:
    *: If no conditions are specifically stated for "Idling", it means the engine for inspection mode, the shift position is in P, the A/C switch is OFF, and accelerator pedal is not depressed.


ACTIVE TEST
It is possible to display items in the DATA LIST during the ACTIVE TEST.

NOTICE:
Beware that if the connector to the Techstream becomes disconnected or a communication error occurs during the ACTIVE TEST, the vehicle could become inoperative (READY light OFF).

HINT:
Performing the ACTIVE TEST using the Techstream enables components including the relay, VSV, and actuator, to be operated without removing any parts. Performing the ACTIVE TEST as the first step of troubleshooting is one method to shorten diagnostic time.

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch ON (IG).

  3. Enter the following menus: Powertrain / Hybrid Control / Active Test.

  4. According to the display on the tester, perform the ACTIVE TEST.

    Tester Display
    Test Part
    Control Range
    Test Details
    Test Condition
    Inspection Mode -2WD Inspection*1, *2
    1. To check its operation while the engine is running
    2. To disable traction control while performing a speedometer test or other test
    ON / OFF
    1. Runs the engine continuously (P position)
    2. Cancels the traction control that is effected when the rotational difference between the front and rear wheels is excessive (other than the P position)
    Power switch ON (IG), HV system normal, not in inspection mode, and other Active Tests not being executed
    Inspection Mode -2WD Chassis-Dynamo*1, *2
    To disable traction control while performing a speedometer test or the like
    ON / OFF
    Cancels the traction control that is effected when the rotational difference between the front and rear wheels is excessive (other than the P position)
    Power switch ON (IG), HV system normal, not in inspection mode, and other Active Tests not being executed
    Forcible Stop of Inverter Drive*1
    To determine if there is an internal leak in the inverter or the HV control ECU
    ON / OFF
    Keeps the inverter power transistor actuation signal ON
    Power switch ON (IG), P position, HV system normal, inverter actuation not being disabled, shutting down inverter, and other Active Tests not being executed
    Compression Test*1, *3, *4
    To crank the engine continuously in order to measure the compression
    ON / OFF
    Allows the engine to continue cranking by activating the generator continuously
    Power switch ON (IG), HV system normal, not in cranking mode, and other Active Tests not being executed

    NOTICE:
    *1: The Techstream displays a communication error and the vehicle's READY light turns OFF when the ACTIVE TEST is completed. Therefore, in order to use the tester again, turn the power switch OFF, and restart by turning it ON.
    *2: After turning on INSPECTION MOD1 or MOD2, push the power switch while depressing the brake pedal.
    *3: After turning on COMPRESS TEST, push the power switch while depressing the brake pedal. To stop engine cranking, push the power switch again.
    *4: COMPRESS TEST may not be activated depending on the condition of the engine or the HV battery.