Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A38-257    Generator Temperature Sensor Circuit Low

DTC    P0A39-259    Generator Temperature Sensor Circuit High

for Preparation Click here


DESCRIPTION

The No. 2 motor temperature sensor detects the temperature of the transaxle fluid. The resistance of the thermistor installed in the No. 2 motor temperature sensor varies with the changes in the transaxle fluid temperature. The construction in the No. 2 motor temperature sensor and how it is connected to the HV control ECU are the same as those of the No. 1 motor temperature sensor .
Based on the signal provided by the No. 2 motor temperature sensor, the HV control ECU limits the load to prevent the motor from overheating. Furthermore, the HV control ECU checks the No. 2 motor temperature sensor for a wiring malfunction and the sensor for a malfunction.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A38
257
GND short in No. 2 motor temperature sensor circuit
  1. Wire harness or connector
  2. Hybrid vehicle motor
  3. HV control ECU
P0A39
259
Open or +B short in No. 2 motor temperature sensor circuit
  1. Wire harness or connector
  2. Hybrid vehicle motor
  3. HV control ECU

HINT:
After confirming DTC P0A38 (INF 257) or P0A39 (INF 259), confirm Motor Temp No2 in DIAGNOSIS / OBD/MOBD / HV ECU / DATA LIST using the Techstream.


Temperature Displayed
Malfunction
-58°F (-50°C)
Open or +B short circuit
401°F (205°C)
GND short circuit

WIRING DIAGRAM


A092299E02


INSPECTION PROCEDURE

1.READ VALUE OF THE TECHSTREAM (MOTOR TEMP NO2)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Engine Control / Data List.

  1. Read the "Motor Temp No2" value.

    Result:

    Temperature Displayed
    Proceed to
    -58°F (-50°C)
    A
    401°F (205°C)
    B
    -57°F to 400°F (-49°C to 204°C)
    C

    HINT:
    1. If there is an open or +B short circuit, the Techstream indicates -58°F (-50°C).
    2. If there is a GND short circuit, the Techstream indicates 401°F (205°C).



B
Go to step 5

C
CHECK FOR INTERMITTENT PROBLEMS
A


2.INSPECT HYBRID VEHICLE MOTOR ASSEMBLY (CHECK FOR OPEN OR +B SHORT)


    A092038E02
  1. Disconnect the M10 No. 2 motor temperature sensor connector.

  1. Turn the power switch ON (IG).



    A092036E03
  1. Measure the voltage between the terminals of the No. 2 motor temperature sensor connector.

    Result:
    Tester Connection
    Voltage
    Proceed to
    OMT (M10-3) - OMTG (M10-6)
    Approximately 5 V
    A
    OMT (M10-3) - OMTG (M10-6)
    9 to 14 V
    B
    OMT (M10-3) - OMTG (M10-6)
    Approximately 0 V
    C

    HINT:
    The No. 2 motor temperature sensor is unavailable as an individual service part. Therefore, when replacing it, the hybrid vehicle motor must be replaced.

  1. Reconnect the No. 2 motor temperature sensor connector.



A
REPLACE HYBRID VEHICLE MOTOR ASSEMBLY

C
Go to step 4
B


3.CHECK HARNESS AND CONNECTOR (CHECK FOR +B SHORT)


    A065743E71
  1. Disconnect the H17 HV control ECU connector.



    A092036E04
  1. Disconnect the M10 No. 2 motor temperature sensor connector.

  1. Turn the power switch ON (IG).

  1. Measure the voltage between the terminal of the No. 2 motor temperature sensor connector and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    OMT (M10-3) - Body ground
    Approximately 0 V

  1. Reconnect the HV control ECU connector.

  1. Reconnect the No. 2 motor temperature sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE CONTROL ECU 

4.READ VALUE OF THE TECHSTREAM (CHECK FOR OPEN IN HYBRID VEHICLE CONTROL ECU)


    A092037E02
  1. Disconnect the M10 No. 2 motor temperature sensor connector.



    A093719E08
  1. Connect terminals OMT and OMTG of the H17 HV control ECU connector.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Engine Control / Data List.

  1. Read the "Motor Temp No2" value.

    OK:
    401°F (205°C)

    HINT:
    If the Techstream indicates a temperature of -58°F (-50°C), check the connection of the HV control ECU. If it is connected normally, replace the HV control ECU.

  1. Reconnect the No. 2 motor temperature sensor connector.



NG
REPLACE HYBRID VEHICLE CONTROL ECU
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

5.READ VALUE OF THE TECHSTREAM (CHECK FOR GND SHORT IN WIRE HARNESS)


    A092038E02
  1. Disconnect the M10 No. 2 motor temperature sensor connector.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Engine Control / Data List.

  1. Read the "Motor Temp No2" value.

    OK:
    -58°F (-50°C)

  1. Reconnect the No. 2 motor temperature sensor connector.

    HINT:
    The No. 2 motor temperature sensor is unavailable as an individual service part. Therefore, when replacing it, the hybrid vehicle motor must be replaced.



OK
REPLACE HYBRID VEHICLE MOTOR ASSEMBLY
NG


6.READ VALUE OF THE TECHSTREAM (CHECK FOR GND SHORT IN HYBRID VEHICLE CONTROL ECU)


    A065743E72
  1. Disconnect the H17 HV control ECU connector.

  1. Turn the power switch ON (IG).



    A092039E02
  1. Enter the following menus: Powertrain / Engine Control / Data List.

  1. Read the "Motor Temp No2" value.

    OK:
    -58°F (-50°C)

  1. Reconnect the HV control ECU connector.



NG
REPLACE HYBRID VEHICLE CONTROL ECU
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR