Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A4B-253    Generator Position Sensor Circuit

DTC    P0A4C-513    Generator Position Sensor Circuit Range / Performance

DTC    P0A4D-255    Generator Position Sensor Circuit Low

for Preparation Click here


DESCRIPTION

The generator resolver detects the position of the magnetic poles, which are indispensable for ensuring the highly efficient control of the MG1 and MG2. The construction of the generator resolver and how it is connected to the HV control ECU are the same as those of the motor resolver .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A4B
253
Interphase short in generator resolver circuit
  1. Wire harness or connector
  2. Hybrid vehicle generator
  3. HV control ECU
P0A4C
513
Generator resolver output is out of normal range
  1. Wire harness or connector
  2. Hybrid vehicle generator
  3. HV control ECU
P0A4D
255
Open or short in generator resolver circuit
  1. Wire harness or connector
  2. Hybrid vehicle generator
  3. HV control ECU

MONITOR DESCRIPTION

The HV control ECU monitors the generator resolver output signal. If the HV control ECU detects output signals that are out of the normal range or specification, it will conclude that there is a malfunction of the generator resolver. The HV control ECU will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0A4B (INF 253):
Generator position sensor circuit malfunction / Short circuit between phases
P0A4C (INF 513):
Generator position sensor circuit malfunction / Range check
P0A4D (INF 255):
Generator position sensor circuit malfunction / Circuit discontinuity or short circuit
Required sensor / components
Generator resolver
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TOYOTA's intellectual property
No other condition
-

TYPICAL MALFUNCTION THRESHOLDS


Generator resolver
Circuit malfunction (interphase shot, open or short), or abnormal output

COMPONENT OPERATING RANGE


Generator resolver
DTCs P0A4B (INF 253) P0A4C (INF 513) and P0A4D (INF 255) are not detected

WIRING DIAGRAM


A092098E02


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - GENERATOR RESOLVER)


    A065743E74
  1. Disconnect the H17 HV control ECU connector.



    A092036E06
  1. Disconnect the M5 generator resolver connector.

  1. Turn the power switch ON (IG).

  1. Measure the voltage between the terminals of the HV control ECU connector and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    GRF (H17-27) - Body ground
    Below 1 V
    GRFG (H17-26) - Body ground
    Below 1 V
    GSN (H17-22) - Body ground
    Below 1 V
    GSNG (H17-21) - Body ground
    Below 1 V
    GCS (H17-23) - Body ground
    Below 1 V
    GCSG (H17-24) - Body ground
    Below 1 V

  1. Turn the power switch OFF.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    GRF (H17-27) - GRF (M5-3)
    Below 1 Ω
    GRFG (H17-26) - GRFG (M5-6)
    Below 1 Ω
    GSN (H17-22) - GSN (M5-2)
    Below 1 Ω
    GSNG (H17-21) - GSNG (M5-5)
    Below 1 Ω
    GCS (H17-23) - GCS (M5-1)
    Below 1 Ω
    GCSG (H17-24) - GCSG (M5-4)
    Below 1 Ω
    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    GRF (H17-27) or GRF (M5-3) - Body ground
    10 kΩ or higher
    GRFG (H17-26) or GRFG (M5-6) - Body ground
    10 kΩ or higher
    GSN (H17-22) or GSN (M5-2) - Body ground
    10 kΩ or higher
    GSNG (H17-21) or GSNG (M5-5) - Body ground
    10 kΩ or higher
    GCS (H17-23) or GCS (M5-1) - Body ground
    10 kΩ or higher
    GCSG (H17-24) or GCSG (M5-4) - Body ground
    10 kΩ or higher

  1. Reconnect the generator resolver connector.

  1. Reconnect the HV control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT GENERATOR RESOLVER
A092040E02
  1. Disconnect the M5 generator resolver connector.

  1. Measure the resistance between the terminals of the generator resolver.

    Standard resistance:
    Tester Connection
    Specified Condition
    GCS (M5-1) - GCSG (M5-4)
    12.6 to 16.8 Ω
    GSN (M5-2) - GSNG (M5-5)
    12.6 to 16.8 Ω
    GRF (M5-3) - GRFG (M5-6)
    7.65 to 10.2 Ω

  1. Using a megohmmeter, measure the insulation resistance between the terminals of the generator resolver.

    Standard resistance:
    Tester Connection
    Specified Condition
    GCS (M5-1) - GSN (M5-2)
    10 MΩ or higher
    GCS (M5-1) - GRF (M5-3)
    10 MΩ or higher
    GSN (M5-2) - GRF (M5-3)
    10 MΩ or higher
    GCSG (M5-4) - GSNG (M5-5)
    10 MΩ or higher
    GCSG (M5-4) - GRFG (M5-6)
    10 MΩ or higher
    GSNG (M5-5) - GRFG (M5-6)
    10 MΩ or higher
    Each terminal listed above - Transaxle housing
    10 MΩ or higher



NG
REPLACE HYBRID VEHICLE GENERATOR ASSEMBLY
OK

REPLACE HYBRID VEHICLE CONTROL ECU