SFI SYSTEM > ECM Power Source Circuit |

| 1.CHECK ECM (+B VOLTAGE) |
![]() |
Turn the power switch ON (IG).
Measure the voltage between the specified terminals of the E5 and E7 ECM connectors.
| Tester Connection | Specified Condition |
| E7-4 (+B) - E5-28 (E1) | 9 to 14 V |
|
| ||||
| NG | |
| 2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) |
![]() |
Disconnect the E5 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| E5-28 (E1) - Body ground | Below 1 Ω |
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.CHECK ECM (IGSW VOLTAGE) |
![]() |
Turn the power switch ON (IG).
Measure the voltage between the specified terminals of the E5 and E6 ECM connectors.
| Tester Connection | Specified Condition |
| E6-9 (IGSW) - E5-28 (E1) | 9 to 14 V |
|
| ||||
| NG | |
| 4.INSPECT FUSE (IGN FUSE) |
![]() |
Remove the IGN fuse from the driver side junction block.
Measure the resistance of the IGN fuse.
Reinstall the IGN fuse.
|
| ||||
| OK | |
| 5.INSPECT INTEGRATION RELAY (IG2 RELAY) |
![]() |
Remove the integration relay from the engine room relay block.
Inspect the IG2 relay.
| Tester Connection | Specified Condition |
| 3K-1 - 3I-4 | 10 kΩ or higher |
| 3K-1 - 3I-4 | Below 1 Ω (Apply battery voltage to terminals 3I-2 and 3I-3) |
Reinstall the integration relay.
|
| ||||
| OK | |
| 6.INSPECT FUSE (AM2 FUSE) |
![]() |
Remove the AM2 fuse from the engine room relay block.
Measure the resistance of the AM2 fuse.
Reinstall the AM2 fuse.
|
| ||||
| OK | ||
| ||
| 7.CHECK ECM (MREL VOLTAGE) |
![]() |
Turn the power switch ON (IG).
Measure the voltage between the specified terminals of the E5 and E7 ECM connectors.
| Tester Connection | Specified Condition |
| E7-7 (MREL) - E5-28 (E1) | 9 to 14 V |
|
| ||||
| OK | |
| 8.INSPECT FUSE (EFI FUSE) |
![]() |
Remove the EFI fuse from the engine room relay block.
Measure the resistance of the EFI fuse.
Reinstall the EFI fuse.
|
| ||||
| OK | |
| 9.INSPECT INTEGRATION RELAY (EFI M RELAY) |
![]() |
Remove the integration relay from the engine room relay block.
Inspect the EFI M relay.
| Tester Connection | Specified Condition |
| 3K-1 - 3I-8 | 10 kΩ or higher |
| 3K-1 - 3I-8 | Below 1 Ω (Apply battery voltage to terminals 3I-6 and 3I-7) |
Reinstall the integration relay.
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (EFI M RELAY - ECM, EFI M RELAY - BODY GROUND) |
Check the harness and connectors between the EFI M relay and ECM connector.
![]() |
Remove the integration relay from the engine room relay block.
![]() |
Disconnect the E7 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| 3I-6 (EFI M relay) - E7-7 (MREL) | Below 1 Ω |
| Tester Connection | Specified Condition |
| 3I-6 (EFI M relay) or E7-7 (MREL) - Body ground | 10 kΩ or higher |
Reinstall the integration relay.
Reconnect the ECM connector.
Check the harness and the connectors between the EFI M relay and the body ground.
Remove the integration relay from the engine room relay block.
Measure the resistance between the wire harness side connector and body ground.
| Tester Connection | Specified Condition |
| 3I-7 (EFI M relay) - Body ground | Below 1 Ω |
Reinstall the integration relay.
|
| ||||
| OK | ||
| ||