Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM (w/ Smart Key System)

ENGINE IMMOBILISER SYSTEM (w/ Smart Key System) > TERMINALS OF ECU

for Preparation Click here



CHECK KEY SLOT

B126055E01

  1. Disconnect the K3 key slot connector.

  2. Measure the resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (K3-7) - Body ground
    P - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the K3 key slot connector.

  4. Measure the resistance and voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (K3-7) - Body ground
    P - Body ground
    Ground
    Always
    Below 1 Ω
    VC5 (K3-1) - GND (K3-7)
    Y - P
    Power source
    No key in key slot
    Below 1 V
    Key inserted
    4.6 to 5.4 V
    CODE (K3-4) - GND (K3-7)
    L - P
    Demodulated signal of key code data
    No key in key slot
    Below 1 V
    Key inserted
    Pulse generation (see waveform 1)
    TXCT (K3-5) - GND (K3-7)
    LG - P
    Key code output signal
    No key in key slot
    Below 1 V
    Key inserted
    Pulse generation (see waveform 2)
    If the result is not as specified, the key slot (amplifier) may have a malfunction.



  5. B135496E01
  6. Using an oscilloscope, check the waveform 1.
    Waveform 1 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    CODE (K3-4) - GND (K3-7)
    Tool Setting
    2 V/DIV., 20 msec./DIV.
    Condition
    Key inserted



  7. B135497E01
  8. Using an oscilloscope, check the waveform 2.
    Waveform 2 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    TXCT (K3-5) - GND (K3-7)
    Tool Setting
    2 V/DIV., 10 msec./DIV.
    Condition
    Key inserted


CHECK TRANSPONDER KEY ECU

B126056E01

  1. Disconnect the T5 ECU connector.

  2. Measure the resistance and voltage of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (T5-22) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    AGND (T5-7) - GND (T5-22)
    P - W-B
    Ground
    Always
    Below 1 Ω
    CPUB (T5-3) - GND (T5-22)
    L - W-B
    +B (CPUB) power supply
    Always
    10 to 14 V
    IG (T5-4) - GND (T5-22)
    O - W-B
    Ignition power supply
    Power switch OFF
    Blow 1 V
    Power switch ON (IG)
    10 to 14 V
    CUWS (T5-5) - GND (T5-22)
    B - W-B
    Halfway switch signal
    No key in key slot
    Below 1 Ω
    Key inserted
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the T5 ECU connector.

  4. Measure the voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    CUWS (T5-5) - GND (T5-22)
    B - W-B
    Halfway switch signal
    No key in key slot
    10 to 14 V
    Key inserted
    Below 1 V
    VC5 (T5-20) - GND (T5-22)
    Y - W-B
    Key slot power source
    No key in key slot
    Below 1 V
    Key inserted
    4.6 to 5.4 V
    CODE (T5-21) - GND (T5-22)
    L - W-B
    Transponder key amplifier communication signal
    No key in key slot
    Below 1 V
    Key inserted
    Pulse generation (see waveform 1)
    TXCT (T5-6) - GND (T5-22)
    LG - W-B
    No key in key slot
    Below 1 V
    Key inserted
    Pulse generation (see waveform 2)
    HEV0 (T5-19) - GND (T5-22)
    W - W-B
    Hybrid vehicle control ECU output signal
    Power switch OFF
    Below 1 V
    Power switch ON (IG)
    Pulse generation (see waveform 3)
    HEV1 (T5-18) - GND (T5-22)
    R - W-B
    Hybrid vehicle control ECU input signal
    Always
    Pulse generation (see waveform 4)
    If the result is not as specified, the ECU may have a malfunction.



  5. B135496E01
  6. Using an oscilloscope, check the waveform 1.
    Waveform 1 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    CODE (T5-21) - GND (T5-22)
    Tool Setting
    2 V/DIV., 20 msec./DIV.
    Condition
    Key inserted



  7. B135497E01
  8. Using an oscilloscope, check the waveform 2.
    Waveform 2 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    TXCT (T5-6) - GND (T5-22)
    Tool Setting
    2 V/DIV., 10 msec./DIV.
    Condition
    Key inserted



  9. B135498E01
  10. Using an oscilloscope, check the waveform 3.
    Waveform 3 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    HEV0 (T5-19) - GND (T5-22)
    Tool Setting
    10 V/DIV., 100 msec./DIV.
    Condition
    Power switch ON (IG)



  11. B135499E01
  12. Using an oscilloscope, check the waveform 4.
    Waveform 4 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    HEV1 (T5-18) - GND (T5-22)
    Tool Setting
    10 V/DIV., 100 msec./DIV.
    Condition
    Always


CHECK CERTIFICATION ECU

B126057E01

  1. Disconnect the S11 ECU connector.

  2. Measure the resistance and voltage of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E (S11-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    +B1 (S11-1) - E (S11-17)
    R - W-B
    Battery power supply
    Always
    10 to 14 V
    KSW (S11-4) - E (S11-17)
    Y - W-B
    Halfway switch signal
    No key in key slot
    10 kΩ or higher
    Key inserted
    Below 1 Ω
    IG (S11-18) - E (S11-17)
    B - W-B
    Ignition switch supply
    Power switch OFF
    Below 1 V
    Power switch ON (IG)
    10 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK HYBRID VEHICLE CONTROL ECU

B126058E01

  1. Measure the resistance and voltage of the connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND1 (H14-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    GND 2 (H14-4) - Body ground
    ST2 (H14-5) - GND1 (H14-1)
    Y - W-B
    Ignition ready control signal input
    Hybrid control system stopped and power switch ON (READY)
    10 to 14 V
    IGSW (H14-7) - GND1 (H14-1)
    O - W-B
    Ignition start control signal input
    Hybrid control system stopped and power switch ON (IG)
    BATT (H15-6) - GND1 (H14-1)
    Y - W-B
    Battery
    Always
    +B1 (H16-7) - GND1 (H14-1)
    L - W-B
    Ignition power supply
    Power switch ON (IG)
    +B2 (H16-6) - GND1 (H14-1)
    IMI (H14-18) - GND2 (H14-4)
    W - W-B
    Transponder key ECU input signal
    Always
    Pulse generation (see waveform 1)
    IMO (H14-26) - GND2 (H14-4)
    R - W-B
    Transponder key ECU output signal
    Power switch OFF
    Below 1 V
    Power switch ON (IG)
    Pulse generation (see waveform 2)
    If the result is not as specified, the ECM may have a malfunction.



  2. B135499E02
  3. Using an oscilloscope, check the waveform 1.
    Waveform 1 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    IMI (H14-18) - GND2 (H14-4)
    Tool Setting
    10 V/DIV., 100 msec./DIV.
    Condition
    Always



  4. B135498E02
  5. Using an oscilloscope, check the waveform 2.
    Waveform 2 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    IMO (H14-26) - GND2 (H14-4)
    Tool Setting
    10 V/DIV., 100 msec./DIV.
    Condition
    Power switch ON (IG)