Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM (w/ Smart Key System)

DTC    B2796    No Communication in Immobiliser System

DTC    B2798    Communication Malfunction No. 2

for Preparation Click here


DESCRIPTION

When a key is inserted into the key slot but no communication occurs between the key and transponder key ECU, DTC B2796 is output. When a key is inserted into the key slot but a communication error occurs between the key and transponder key ECU, DTC B2798 is output.

DTC No.
DTC Detection Condition
Trouble Area
B2796
No communication
  1. Key (door control transmitter)
  2. Wire harness
  3. Key slot
  4. Transponder key ECU
B2798
Communication error
Key (door control transmitter)

WIRING DIAGRAM


B121682E14


INSPECTION PROCEDURE

1.READ VALUE OF TECHSTREAM (ENGINE IMMOBILISER SYSTEM)
  1. Check the Data List for proper functioning of the engine immobiliser system.

    Transponder Key ECU: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Immobiliser
    Engine immobiliser system status / SET or UNSET
    SET: No key is in key slot
    UNSET: Power switch ON (IG)
    -

    OK:
    "UNSET" (power switch ON (IG)) appears on screen.



OK
REPLACE TRANSPONDER KEY ECU
NG


2.CHECK DOOR CONTROL TRANSMITTER (OPERATION)
  1. Temporarily replace the door control transmitter with a new or normally functioning one.

  1. Check that change the power switch can be turned ON (IG).

    OK:
    Power switch can be turned ON (ACC and IG) and hybrid control system can be started.



OK
END (DOOR CONTROL TRANSMITTER IS DEFECTIVE)
NG


3.READ VALUE OF TECHSTREAM (TRANSPONDER KEY COIL)
  1. Check the Data List for proper functioning of the transponder key coil.

    Transponder Key ECU: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Antenna Coil
    Transponder key coil condition / NORMAL or FAIL
    NORMAL: Transponder key coil is normal
    FAIL: Transponder key coil is malfunctioning
    -

    OK:
    "NORMAL" (transponder key coil is normal) is appears on screen.



NG
REPLACE KEY SLOT
OK


4.CHECK WIRE HARNESS (TRANSPONDER KEY ECU - KEY SLOT)


    B126099E01
  1. Disconnect the T5 ECU connector.

  1. Disconnect the K3 key slot connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    T5-20 (VC5) - K3-1 (VC5)
    Below 1 Ω
    T5-21 (CODE) - K3-4 (CODE)
    T5-6 (TXCT) - K3-5 (TXCT)
    T5-7 (AGND) - K3-7 (GND)
    T5-20 (VC5) or K3-1 (VC5) - Body ground
    10 kΩ or higher
    T5-21 (CODE) or K3-4 (CODE) - Body ground
    T5-6 (TXCT) or K3-5 (TXCT) - Body ground
    T5-7 (AGND) or K3-7 (GND) - Body ground



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.CHECK KEY SLOT (OPERATION)
  1. Temporarily replace the key slot with a new or normally functioning one.

  1. Check that the power switch can be turned ON (ACC and IG) and the hybrid control system can be started.

    OK:
    Power switch can be turned ON (ACC and IG) and hybrid control system can be started.



NG
REPLACE TRANSPONDER KEY ECU
OK

END (KEY SLOT IS DEFECTIVE)