Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A94-583    DC / DC Converter Performance

DTC    P0A94-584    DC / DC Converter Performance

for Preparation Click here


DESCRIPTION


A180545E01

See the description of the boost converter .
The HV control ECU uses a temperature sensor, which is built into the boost converter, to detect the temperature of the boost converter.
The boost converter temperature sensor outputs a voltage, which varies between 0 and 5 V in accordance with the changes in the temperature. The higher the boost converter temperature, the lower the output voltage. Conversely, the lower the temperature, the higher the output voltage.
The HV control ECU limits the load based on the signals transmitted by the boost converter temperature sensor, in order to prevent the boost converter from overheating. Furthermore, the HV control ECU detects a malfunction in the wiring of the boost converter temperature sensor, as well as in the sensor itself.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A94
583
Open or GND short in boost converter temperature sensor circuit
  1. Wire harness or connector
  2. Inverter with converter assembly
  3. HV control ECU
P0A94
584
+B short in boost converter temperature sensor circuit
  1. Wire harness or connector
  2. Inverter with converter assembly
  3. HV control ECU

HINT:
After confirming DTC P0A94 (INF 583 or 584), confirm Converter Temperature in DIAGNOSIS / OBD/MOBD / HV ECU / DATA LIST using the Techstream.


Temperature Displayed
Malfunction
-58°F (-50°C)
+B short circuit
401°F (205°C)
Open or GND short circuit

MONITOR DESCRIPTION

The HV control ECU monitors the boost converter temperature sensor circuit. If the HV control ECU detects an open or short malfunction of the sensor circuit, the HV control ECU illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0A94 (INF 583 / 584):
Boost converter / Converter temperature sensor malfunction
Required sensor / components
Boost converter
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TOYOTA's intellectual property
Other conditions belong to TOYOTA's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


Boost converter temperature sensor circuit
Open or short

COMPONENT OPERATING RANGE


Boost converter
DTC P0A94 (INF 583 / 584) is not detected

WIRING DIAGRAM


A092106E05


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from reconnecting it while you are servicing the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes are required to discharge the high-voltage condenser inside the inverter.

1.READ VALUE OF THE TECHSTREAM (CONVERTER TEMPERATURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Engine Control / Data List.

  1. Read the "Converter Temperature" value.

    Result:

    Temperature Displayed
    Proceed to
    -58°F (-50°C)
    A
    401°F (205°C)
    B
    -57°F to 400°F (-49°C to 204°C)
    C

    HINT:
    1. If there is a +B short circuit, the Techstream indicates -58°F (-50°C).
    2. If there is an open or GND short circuit, the Techstream indicates 401°F (205°C).



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS
A


2.READ VALUE OF THE TECHSTREAM (CHECK FOR +B SHORT IN WIRE HARNESS)

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.

  1. Remove the inverter cover .



    A092041E25
  1. Disconnect the I10 inverter connector.



    A125426E02
  1. Turn the power switch ON (IG).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and inverter cover removed.

  1. Enter the following menus: Powertrain / Engine Control / Data List.

  1. Read the "Converter Temperature" value.

    OK:
    401°F (205°C)

  1. Turn the power switch OFF.

  1. Reconnect the inverter connector.

  1. Reinstall the inverter cover .

  1. Reinstall the service plug grip .



OK
REPLACE INVERTER WITH CONVERTER ASSEMBLY
NG


3.READ VALUE OF THE TECHSTREAM (CHECK FOR +B SHORT IN HYBRID VEHICLE CONTROL ECU)


    A065745E39
  1. Disconnect the H16 HV control ECU connector.



    A126232E01
  1. Turn the power switch ON (IG).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and inverter cover removed.

  1. Enter the following menus: Powertrain / Engine Control / Data List.

  1. Read the "Converter Temperature" value on the Techstream.

    OK:
    401°F (205°C)

  1. Reconnect the HV control ECU connector.



NG
REPLACE HYBRID VEHICLE CONTROL ECU
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER)

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.

  1. Remove the inverter cover .



    A065745E39
  1. Disconnect the H16 HV control ECU connector.



    A092041E25
  1. Disconnect the I10 inverter connector.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    CT (H16-21) - CT (I10-14)
    Below 1 Ω
    GCNV (H16-8) - GCNV (I10-32)
    Below 1 Ω
    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    CT (H16-21) or CT (I10-14) - Body ground
    10 kΩ or higher
    GCNV (H16-8) or GCNV (I10-32) - Body ground
    10 kΩ or higher

  1. Reconnect the inverter connector.

  1. Reconnect the HV control ECU connector.

  1. Reinstall the inverter cover .

  1. Reinstall the service plug grip .



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT HYBRID VEHICLE CONTROL ECU (CT VOLTAGE)
  1. Turn the power switch ON (IG).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and inverter cover removed.



    A093719E01
  1. Measure the voltage between the terminals of the H16 HV control ECU connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    CT (H16-21) - GCNV (H16-8)
    2.0 to 4.5 V



NG
REPLACE INVERTER WITH CONVERTER ASSEMBLY
OK

REPLACE HYBRID VEHICLE CONTROL ECU