Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A94-587    DC / DC Converter Performance

for Preparation Click here


DESCRIPTION

See the description of the boost converter .
The HV control ECU uses two voltage sensors, VL and VB, to detect voltage levels. The VL sensor that has been built into the boost converter is used to detect the high voltage before it is boosted. The VB sensor that has been built into the battery ECU is used to detect voltage of the HV battery.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A94
587
Difference between voltages from HV battery voltage (VB) sensor and boost converter voltage (VL) sensor is large
  1. Wire harness or connector
  2. Inverter with converter assembly
  3. Service plug grip
  4. High voltage fuse
  5. Battery ECU

MONITOR DESCRIPTION

The HV control ECU monitors signals of HV battery voltage (VB) and boost converter voltage (VL) sensors. When a large difference occurs between the voltages from the VB and VL sensors, the HV control ECU interprets this as a failure of either of the sensors. The HV control ECU then illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0A94 (INF 587):
Voltage (VB or VL) sensor deviation
Required sensor / components
Boost converter, battery ECU
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TOYOTA's intellectual property
Other conditions belong to TOYOTA's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


Difference between the voltages of HV battery and boost converter voltage sensors
Exceeds the standard level

COMPONENT OPERATING RANGE


Boost converter
Battery ECU
DTC P0A94 (INF 587) is not detected

WIRING DIAGRAM

Refer to DTC P0A94 (INF 589) .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from reconnecting it while you are servicing the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes are required to discharge the high-voltage condenser inside the inverter.

1.READ OUTPUT DTC (HV ECU)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:

    Display (DTC Output)
    Proceed to
    Only DTC P0A94 (INF 587)
    A
    DTCs P0A94 (INF 587), and P0A1F (INF 129) (HV battery voltage circuit malfunction)
    B
    DTCs P0A94 (INF 587), and P0A94 (INF 442) (Abnormal voltage execution value)
    C
    DTCs P0A94 (INF 587), and P0A94 (INF 585) (Boost converter voltage (VL) sensor performance problem)
    D
    DTCs other than above
    E



B
GO TO DTC P0A1F-129

C
Go to step 4

D
GO TO DTC P0A94-585

E
AFTER PERFORMING "CHECK HARNESS AND CONNECTOR" PROCEDURE, GO TO RELEVANT DTC CHART
A


2.READ OUTPUT DTC (HV BATTERY)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    DTCs are output



YES
GO TO RELEVANT DTC CHART
NO


3.INSPECT SERVICE PLUG GRIP

CAUTION:
Wear insulated gloves before performing the following operation.



    A081749E02
  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.

  1. Measure the resistance between the terminals of the service plug grip.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the service plug grip .



NG
Go to step 6
OK


4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER)

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.



    A065745E40
  1. Disconnect the H16 HV control ECU connector.

  1. Remove the inverter cover .



    A092041E27
  1. Disconnect the I10 inverter connector.

  1. Turn the power switch ON (IG).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and inverter cover removed.

  1. Measure the voltage between the terminals of the HV control ECU connector and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    VL (H16-30) - Body ground
    Below 1 V
    GCNV (H16-8) - Body ground
    Below 1 V

  1. Turn the power switch OFF.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    VL (H16-30) - VL (I10-15)
    Below 1 Ω
    GCNV (H16-8) - GCNV (I10-32)
    Below 1 Ω
    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    VL (H16-30) or VL (I10-15) - Body ground
    10 kΩ or higher
    GCNV (H16-8) or GCNV (I10-32) - Body ground
    10 kΩ or higher

  1. Reconnect the inverter connector.

  1. Reconnect the HV control ECU connector.

  1. Reinstall the inverter cover .

  1. Reinstall the service plug grip .



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK OUTPUT DTC
  1. Proceed to A if only DTC P0A94 (INF 587) is output as a result of DTC reading in the "READ OUTPUT DTC" procedure.

  1. Proceed to B if DTCs P0A94 (INF 587) and P0A94 (INF 442) are output as a result of DTC reading in the "READ OUTPUT DTC" procedure.



B
REPLACE INVERTER WITH CONVERTER ASSEMBLY
A

REPLACE INVERTER WITH CONVERTER ASSEMBLY AND BATTERY ECU ASSEMBLY 

6.INSPECT HIGH VOLTAGE FUSE

CAUTION:
Wear insulated gloves before performing the following operation.



    A057824E02
  1. Remove the high voltage fuse .

    HINT:
    The high voltage fuse is enclosed in the service plug grip.

  1. Measure the resistance between the terminals of the high voltage fuse.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the high voltage fuse .



NG
REPLACE HIGH VOLTAGE FUSE
OK

REPLACE SERVICE PLUG GRIP