Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A94-589    DC / DC Converter Performance

DTC    P0A94-590    DC / DC Converter Performance

for Preparation Click here


DESCRIPTION

A125422E01
See the description of the boost converter .
The HV control ECU uses a voltage sensor, which has been built into the boost converter, to detect the high voltage before it is boosted and for boost control.
The boost converter voltage sensor outputs a voltage that varies between 0 and 5 V in accordance with the changes in the high voltage. The higher the high voltage, the higher the output voltage, and the lower the high voltage, the lower the output voltage.
The HV control ECU monitors a signal line of the boost converter voltage sensor and detects a malfunction.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A94
589
Open or GND short in boost converter voltage (VL) sensor circuit
  1. Wire harness or connector
  2. Inverter with converter assembly
  3. HV control ECU
P0A94
590
+B short in boost converter voltage (VL) sensor circuit
  1. Wire harness or connector
  2. Inverter with converter assembly
  3. HV control ECU

HINT:
After confirming DTC P0A94 (INF 589 or 590), confirm VL-Voltage before Boosting in Powertrain / Engine Control / Data List using the Techstream.


Voltage Displayed
Malfunction
510 V
+B short circuit
0 V
Open or GND short circuit

MONITOR DESCRIPTION

The HV control ECU monitors the boost converter voltage (VL) sensor circuit. If the HV control ECU detects an open or short malfunction of the VL sensor circuit, the HV control ECU illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0A94 (INF 589 / 590): Boost converter / VL malfunction
Required sensor / components
Boost converter
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TOYOTA's intellectual property
Other conditions belong to TOYOTA's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


Boost converter voltage sensor circuit
Short

COMPONENT OPERATING RANGE


Boost converter
DTC P0A94 (INF 589 / 590) is not detected

WIRING DIAGRAM


A092106E07


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from reconnecting it while you are servicing the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes are required to discharge the high-voltage condenser inside the inverter.

1.READ VALUE OF THE TECHSTREAM (VL-VOLTAGE BEFORE BOOSTING)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Engine Control / Data List.

  1. Read the "VL-Voltage before Boosting" value.

    Result:

    Voltage Displayed
    Proceed to
    510 V
    A
    0 V
    B
    1 to 509 V
    C

    HINT:
    1. If there is a +B short circuit, the Techstream indicates 510 V.
    2. If there is an open or GND short circuit, the Techstream indicates 0 V.



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS
A


2.READ VALUE OF THE TECHSTREAM (CHECK FOR +B SHORT IN WIRE HARNESS)

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.

  1. Remove the inverter cover .



    A092041E29
  1. Disconnect the I10 inverter connector.



    A125426E03
  1. Turn the power switch ON (IG).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and inverter cover removed.

  1. Enter the following menus: Powertrain / Engine Control / Data List.

  1. Read the "VL-Voltage before Boosting" value.

    Standard voltage:
    0 V

  1. Turn the power switch OFF.

  1. Reconnect the inverter connector.

  1. Reinstall the inverter cover .

  1. Reinstall the service plug grip .



OK
REPLACE INVERTER WITH CONVERTER ASSEMBLY
NG


3.READ VALUE OF THE TECHSTREAM (CHECK FOR +B SHORT IN HYBRID VEHICLE CONTROL ECU)


    A065745E40
  1. Disconnect the H16 HV control ECU connector.



    A126232E02
  1. Turn the power switch ON (IG).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and the inverter cover removed.

  1. Enter the following menus: Powertrain / Engine Control / Data List.

  1. Read the "VL-Voltage before Boosting" value.

    Standard voltage:
    0 V

  1. Reconnect the HV control ECU connector.



NG
REPLACE HYBRID VEHICLE CONTROL ECU
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER)

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.

  1. Remove the inverter cover .



    A065745E40
  1. Disconnect the H16 HV control ECU connector.



    A092041E29
  1. Disconnect the I10 inverter connector.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    VL (H16-30) - VL (I10-15)
    Below 1 Ω
    GCNV (H16-8) - GCNV (I10-32)
    Below 1 Ω
    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    VL (H16-30) or VL (I10-15) - Body ground
    10 kΩ or higher
    GCNV (H16-8) or GCNV (I10-32) - Body ground
    10 kΩ or higher

  1. Reconnect the inverter connector.

  1. Reconnect the HV control ECU connector.

  1. Reinstall the inverter cover .

  1. Reinstall the service plug grip .



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HYBRID VEHICLE CONTROL ECU (VL VOLTAGE)


    A093719E19
  1. Turn the power switch ON (READY).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and inverter cover removed.

  1. Measure the voltage between the terminals of the H16 HV control ECU connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    VL (H16-30) - GCNV (H16-8)
    1.9 to 3.4 V



NG
REPLACE INVERTER WITH CONVERTER ASSEMBLY
OK

REPLACE HYBRID VEHICLE CONTROL ECU