Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P3226-562    DC/DC Boost Converter Temperature Sensor

DTC    P3226-563    DC/DC Boost Converter Temperature Sensor

for Preparation Click here


DESCRIPTION

Refer to DTC P0A94 (INF 583) .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P3226
562
Sudden change in boost converter temperature sensor output
  1. Wire harness or connector
  2. Inverter cooling system
  3. Water pump with assembly
  4. Cooling fan motor
  5. No. 2 cooling fan motor
  6. Inverter with converter assembly
P3226
563
Boost converter temperature sensor output deviation
  1. Wire harness or connector
  2. Inverter cooling system
  3. Water pump with motor assembly
  4. Cooling fan motor
  5. No. 2 cooling fan motor
  6. Inverter with converter assembly

WIRING DIAGRAM

Refer to DTC P0A94 (INF 583) .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from reconnecting it while you are servicing the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes are required to discharge the high-voltage condenser inside the inverter.

1.CHECK QUANTITY OF HV COOLANT
  1. Check that there is a sufficient amount of coolant for the inverter.

    OK:
    There is a sufficient amount of coolant for the inverter



NG
ADD HV COOLANT
OK


2.CHECK COOLANT HOSE
  1. Check that the hoses of the cooling system are not bent or clogged (refer to the cooling system [Click here]).

    OK:
    The hoses of the cooling system are not bent or clogged



NG
CORRECT TO NORMAL CONDITION
OK


3.CHECK CONNECTION CONDITION OF WATER PUMP CONNECTOR (LOOSENESS AND POOR CONTACT)


    A090415E01
  1. Check the connection condition of the water pump connector.

    OK:
    Connector has been connected securely and there is no poor connection.



NG
CONNECT SECURELY
OK


4.CHECK WATER PUMP WITH MOTOR ASSEMBLY
  1. Turn the power switch ON (IG).

  1. Check the operation of the water pump.

    OK:
    Coolant is sloshing in the reservoir tank



NG
REPLACE WATER PUMP WITH MOTOR ASSEMBLY
OK


5.CHECK CONNECTION CONDITION OF COOLING FAN MOTOR CONNECTOR (LOOSENESS AND POOR CONTACT)


    A090546E01
  1. Check the connection condition of the cooling fan motor connectors.

    OK:
    Connectors have been connected securely and there is no poor connection.



NG
CONNECT SECURELY
OK


6.INSPECT COOLING FAN MOTOR
  1. Inspect the cooling fan motor .



NG
REPLACE COOLING FAN MOTOR AND ADD ENGINE COOLANT
OK


7.INSPECT NO. 2 COOLING FAN MOTOR
  1. Inspect the No. 2 cooling fan motor .



NG
REPLACE NO. 2 COOLING FAN MOTOR AND ADD ENGINE COOLANT
OK


8.CHECK CONNECTION CONDITION OF HYBRID VEHICLE CONTROL ECU CONNECTOR (LOOSENESS AND POOR CONTACT)


    A093719E09
  1. Check the connection condition of all the connectors at the HV control ECU.

    OK:
    Connectors have been connected securely and there is no poor connection.



NG
CONNECT SECURELY
OK


9.CHECK CONNECTION CONDITION OF INVERTER CONNECTOR (LOOSENESS AND POOR CONTACT)

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.

  1. Remove the inverter cover .



    A092044E02
  1. Check the connection condition of the I9 and I10 inverter connectors.

    OK:
    Connectors have been connected securely and there is no poor connection.



NG
CONNECT SECURELY
OK


10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER)

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Check that the service plug grip and inverter cover have been removed.



    A065745E51
  1. Disconnect the H16 HV control ECU connector.



    A092063E07
  1. Disconnect the I9 and I10 inverter connectors.

  1. Turn the power switch ON (IG).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and inverter cover removed.

  1. Measure the voltage between the terminals of the HV control ECU connector and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    CT (H16-21) - Body ground
    Below 1 V
    GCNV (H16-8) - Body ground
    Below 1 V

  1. Turn the power switch OFF.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    CT (H16-21) - CT (I10-14)
    Below 1 Ω
    GCNV (H16-8) - GCNV (I10-32)
    Below 1 Ω
    Standard (Check for short):
    Tester Connection
    Specified Condition
    CT (H16-21) or CT (I10-14) - Body ground
    10 kΩ or higher
    GCNV (H16-8) or GCNV (I10-32) - Body ground
    10 kΩ or higher

  1. Reconnect the inverter connectors.

  1. Reconnect the HV control ECU connector.

  1. Reinstall the inverter cover .

  1. Reinstall the service plug grip .



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY