Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A72-326    Generator Phase V Current

DTC    P0A72-327    Generator Phase V Current

DTC    P0A72-328    Generator Phase V Current

DTC    P0A72-330    Generator Phase V Current

DTC    P0A72-333    Generator Phase V Current

DTC    P0A72-515    Generator Phase V Current

DTC    P0A75-334    Generator Phase W Current

DTC    P0A75-335    Generator Phase W Current

DTC    P0A75-336    Generator Phase W Current

DTC    P0A75-338    Generator Phase W Current

DTC    P0A75-341    Generator Phase W Current

DTC    P0A75-516    Generator Phase W Current

for Preparation Click here


DESCRIPTION

Refer to DTC P0A60 (INF 288) .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A72
326
Phase V current sub sensor of generator inverter current sensor malfunction
  1. Wire harness or connector
  2. Inverter with converter assembly
P0A72
327
Open in phase V current sub sensor circuit of generator inverter current sensor
  1. Wire harness or connector
  2. Inverter with converter assembly
P0A72
328
Phase V current main sensor of generator inverter current sensor malfunction
  1. Wire harness or connector
  2. Inverter with converter assembly
P0A72
330
Open in phase V current main sensor circuit of generator inverter current sensor
  1. Wire harness or connector
  2. Inverter with converter assembly
P0A72
333
Phase V current main and sub sensors of generator inverter current sensor performance problem
  1. Wire harness or connector
  2. Inverter with converter assembly
P0A72
515
Phase V current main and sub sensors of generator inverter current sensor offset malfunction
  1. Wire harness or connector
  2. Inverter with converter assembly
P0A75
334
Phase W current sub sensor of generator inverter current sensor malfunction
  1. Wire harness or connector
  2. Inverter with converter assembly
P0A75
335
Open in phase W current sub sensor circuit of generator inverter current sensor
  1. Wire harness or connector
  2. Inverter with converter assembly
P0A75
336
Phase W current main sensor of generator inverter current sensor malfunction
  1. Wire harness or connector
  2. Inverter with converter assembly
P0A75
338
Open in phase W current main sensor circuit of generator inverter current sensor
  1. Wire harness or connector
  2. Inverter with converter assembly
P0A75
341
Phase W current main and sub sensors of generator inverter current sensor performance problem
  1. Wire harness or connector
  2. Inverter with converter assembly
P0A75
516
Phase W current main and sub sensors of generator inverter current sensor offset malfunction
  1. Wire harness or connector
  2. Inverter with converter assembly

MONITOR DESCRIPTION

The HV control ECU monitors the generator inverter current sensor. If the HV control ECU detects a fault, it will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0A72 (INF 326 / 327 / 328 / 330 / 333 / 515):
Generator inverter current sensor / Phase V current sensor malfunction
P0A75 (INF 334 / 335 / 336 / 338 / 341 / 516):
Generator inverter current sensor / Phase W current sensor malfunction
Required sensor / components
Generator inverter current sensor, generator resolver
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TOYOTA's intellectual property
Other conditions belong to TOYOTA's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TOYOTA's intellectual property
-

COMPONENT OPERATING RANGE


P0A72 (INF 326 / 327 / 328 / 330 / 333 / 515): 
Generator inverter current sensor
DTC P0A72 (INF 326 / 327 / 328 / 330 / 333 / 515) is not detected

P0A75 (INF 334 / 335 / 336 / 338 / 341 / 516): 
Generator inverter current sensor
DTC P0A75 (INF 334 / 335 / 336 / 338 / 341 / 516) is not detected

WIRING DIAGRAM


A092099E03


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from reconnecting it while you are servicing the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes are required to discharge the high-voltage condenser inside the inverter.

1.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER)

NOTICE:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.



    A065744E44
  1. Disconnect the H15 HV control ECU connector.

  1. Remove the inverter cover .



    A092041E31
  1. Disconnect the I10 inverter connector.

  1. Turn the power switch ON (IG).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and inverter cover removed.

  1. Measure the voltage between the terminals of the HV control ECU connector and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    GIVA (H15-34) - Body ground
    Below 1 V
    GIVB (H15-33) - Body ground
    Below 1 V
    GIWA (H15-32) - Body ground
    Below 1 V
    GIWB (H15-31) - Body ground
    Below 1 V
    GINV (H15-23) - Body ground
    Below 1 V

  1. Turn the power switch OFF.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    GIVA (H15-34) - GIVA (I10-2)
    Below 1 Ω
    GIVB (H15-33) - GIVB (I10-3)
    Below 1 Ω
    GIWA (H15-32) - GIWA (I10-18)
    Below 1 Ω
    GIWB (H15-31) - GIWB (I10-19)
    Below 1 Ω
    GINV (H15-23) - GINV (I10-16)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    GIVA (H15-34) or GIVA (I10-2) - Body ground
    10 kΩ or higher
    GIVB (H15-33) or GIVB (I10-3) - Body ground
    10 kΩ or higher
    GIWA (H15-32) or GIWA (I10-18) - Body ground
    10 kΩ or higher
    GIWB (H15-31) or GIWB (I10-19) - Body ground
    10 kΩ or higher
    GINV (H15-23) or GINV (I10-16) - Body ground
    10 kΩ or higher

  1. Reconnect the inverter connector.

  1. Reconnect the HV control ECU connector.

  1. Reinstall the inverter cover .

  1. Reinstall the service plug grip .



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY