Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A78-266    Drive Motor "A" Inverter Performance

DTC    P0A78-267    Drive Motor "A" Inverter Performance

for Preparation Click here


DESCRIPTION

The inverter converts the high-voltage direct current of the HV battery and the alternating current for the MG1/MG2. The inverter contains a three-phase bridge circuit, which consists of 6 power transistors each for the MG1 and the MG2, in order to convert the direct current and the three-phase alternating current. The HV control ECU controls the actuation of the power transistors.
The inverter transmits information that is necessary for effecting control, such as the amperage and voltage, to the HV control ECU.

A093740E02

The HV control ECU uses a voltage sensor, which has been built into the inverter, to detect the high voltage after boost control.
A125422E01
The inverter voltage sensor outputs a voltage that varies between 0 and 5 V in accordance with the changes in the high voltage. The higher the high voltage, the higher the output voltage, and the lower the high voltage, the lower the output voltage.
The HV control ECU monitors the inverter voltage and detects a malfunction.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A78
266
Open or GND short in inverter voltage (VH) sensor circuit
  1. Wire harness or connector
  2. Inverter with converter assembly
  3. HV control ECU
P0A78
267
+B short in inverter voltage (VH) sensor circuit
  1. Wire harness or connector
  2. Inverter with converter assembly
  3. HV control ECU

HINT:
After confirming DTC P0A78 (INF 266 or 267), confirm "VH-Voltage after Boosting" in Powertrain / Engine Control / Data List using the Techstream.


Voltage Displayed
Malfunction
765 V
+B short circuit
0 V
Open or GND short circuit

MONITOR DESCRIPTION

The HV control ECU monitors the inverter voltage (VH) sensor circuit. If the HV control ECU detects an open or short malfunction of the VH sensor circuit, the HV control ECU illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0A78 (INF 266 / 267): Motor inverter / VH malfunction
Required sensor / components
Motor inverter
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TOYOTA's intellectual property
Other conditions belong to TOYOTA's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


Voltage (VH) sensor circuit
Open or short

COMPONENT OPERATING RANGE


Motor inverter
DTC P0A78 (INF 266 / 267) is not detected

WIRING DIAGRAM


A092100E03


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from reconnecting it while you are servicing the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes are required to discharge the high-voltage condenser inside the inverter.

1.READ OUTPUT DTC (HV ECU)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    DTC P0A1D is output



YES
GO TO RELEVANT DTC CHART
NO


2.READ VALUE OF THE TECHSTREAM (VH-VOLTAGE AFTER BOOSTING)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Engine Control / Data List.

  1. Read the "VH-Voltage after Boosting" value.


Result:

Voltage Displayed
Proceed to
765 V
A
0 V
B
1 to 764 V
C

HINT:
  1. If there is a +B short circuit, the Techstream indicates 765 V.
  2. If there is an open or GND short circuit, the Techstream indicates 0 V.



B
Go to step 5

C
CHECK FOR INTERMITTENT PROBLEMS
A


3.READ VALUE OF THE TECHSTREAM (CHECK FOR +B SHORT IN WIRE HARNESS)

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.

  1. Remove the inverter cover .



    A092041E35
  1. Disconnect the I10 inverter connector.



    A125426E01
  1. Turn the power switch ON (IG).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and inverter cover removed.

  1. Enter the following menus: Powertrain / Engine Control / Data List.

  1. Read the "VH-Voltage after Boosting" value.

    Standard voltage:
    0 V

  1. Turn the power switch OFF.

  1. Reconnect the inverter connector.

  1. Reinstall the inverter cover .

  1. Reinstall the service plug grip .



OK
REPLACE INVERTER WITH CONVERTER ASSEMBLY
NG


4.READ VALUE OF THE TECHSTREAM (CHECK FOR +B SHORT IN HYBRID VEHICLE CONTROL ECU)


    A065744E45
  1. Disconnect the H15 HV control ECU connector.



    A126232E05
  1. Turn the power switch ON (IG).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and inverter cover removed.

  1. Enter the following menus: Powertrain / Engine Control / Data List.

  1. Read the "VH-Voltage after Boosting" value.

    Standard voltage:
    0 V

  1. Reconnect the HV control ECU connector.



NG
REPLACE HYBRID VEHICLE CONTROL ECU
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER)

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.

  1. Remove the inverter cover .



    A065744E45
    A092041E35
  1. Disconnect the H15 HV control ECU connector.

  1. Disconnect the I10 inverter connector.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    VH (H15-26) - VH (I10-12)
    Below 1 Ω
    GINV (H15-23) - GINV (I10-16)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    VH (H15-26) or VH (I10-12) - Body ground
    10 kΩ or higher
    GINV (H15-23) or GINV (I10-16) - Body ground
    10 kΩ or higher

  1. Reconnect the inverter connector.

  1. Reconnect the HV control ECU connector.

  1. Reinstall the inverter cover .

  1. Reinstall the service plug grip .



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT HYBRID VEHICLE CONTROL ECU (VH VOLTAGE)


    A124045E16
  1. Turn the power switch ON (READY).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and inverter cover removed.

  1. Measure the voltage between the terminals of the H15 HV control ECU connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    VH (H15-26) - GINV (H15-23)
    1.6 to 3.8 V



NG
REPLACE INVERTER WITH CONVERTER ASSEMBLY
OK

REPLACE HYBRID VEHICLE CONTROL ECU