Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A78-278    Drive Motor "A" Inverter Performance

DTC    P0A78-280    Drive Motor "A" Inverter Performance

for Preparation Click here


DESCRIPTION

See the description of the inverter .
If the motor inverter detects a circuit malfunction or over-voltage, the inverter transmits this information to the OVH terminal of the HV control ECU via the motor inverter over-voltage signal line.
The HV control ECU monitors the motor inverter over-voltage signal line to detect the malfunction.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A78
278
+B short in motor inverter over-voltage (OVH) signal circuit
  1. Wire harness or connector
  2. Inverter with converter assembly
P0A78
280
Open or GND short in motor inverter over-voltage (OVH) signal circuit
  1. Wire harness or connector
  2. Inverter with converter assembly

MONITOR DESCRIPTION

The HV control ECU monitors the motor inverter over-voltage (OVH) signal line. If the HV control ECU detects an open or short malfunction of the OVH signal circuit, the HV control ECU illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0A78 (INF 278 / 280): Motor inverter / Motor inverter Sinv detection
Required sensor / components
Motor inverter
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TOYOTA's intellectual property
Other conditions belong to TOYOTA's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


Over-voltage signal circuit
Open or short

COMPONENT OPERATING RANGE


Motor inverter
DTC P0A78 (INF 278 / 280) is not detected

WIRING DIAGRAM


A092102E06


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from reconnecting it while you are servicing the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes are required to discharge the high-voltage condenser inside the inverter.

1.CHECK HARNESS AND CONNECTOR (HYBRID CONTROL ECU - INVERTER)

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.



    A065744E77
  1. Disconnect the H15 HV control ECU connector.

  1. Remove the inverter cover .



    A092041E37
  1. Disconnect the I10 inverter connector.

  1. Turn the power switch ON (IG).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and inverter cover removed.

  1. Measure the voltage between the terminals of the HV control ECU connector and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    OVH (H15-22) - Body ground
    Below 1 V
    GINV (H15-23) - Body ground
    Below 1 V

  1. Turn the power switch OFF.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    OVH (H15-22) - OVH (I10-28)
    Below 1 Ω
    GINV (H15-23) - GINV (I10-16)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    OVH (H15-22) or OVH (I10-28) - Body ground
    10 kΩ or higher
    GINV (H15-23) or GINV (I10-16) - Body ground
    10 kΩ or higher

  1. Reconnect the inverter connector.

  1. Reconnect the HV control ECU connector.

  1. Reinstall the inverter cover .

  1. Reinstall the service plug grip .



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY