Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A7A-309    Generator Inverter Performance

for Preparation Click here


DESCRIPTION

Refer to DTC P0A78 (INF 272) .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A7A
309
Abnormality in generator PWM circuit
  1. Wire harness or connector
  2. Inverter with converter assembly

MONITOR DESCRIPTION

The HV control ECU monitors the generator PWM circuit. If there is an error in the power transistor actuation signals which are transmitted to the inverter, the HV control ECU interprets this as a malfunction of the generator PWM circuit.
The HV control ECU illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0A7A (INF 309):
Generator PWM malfunction
Required sensor / components
Generator inverter
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TOYOTA's intellectual property
Other conditions belong to TOYOTA's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


Power transistor actuation signal
Abnormal

COMPONENT OPERATING RANGE


Generator inverter
DTC P0A7A (INF 309) is not detected

WIRING DIAGRAM


A092101E03


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from reconnecting it while you are servicing the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes are required to discharge the high-voltage condenser inside the inverter.

1.READ OUTPUT DTC (HV ECU)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    DTC P0A1D is output



YES
GO TO RELEVANT DTC CHART
NO


2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER)

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.

  1. Remove the inverter cover .



    A065744E30
  1. Disconnect the H15 HV control ECU connector.



    A092041E41
  1. Disconnect the I10 inverter connector.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    GUU (H15-15) - GUU (I10-4)
    Below 1 Ω
    GVU (H15-14) - GVU (I10-5)
    Below 1 Ω
    GWU (H15-13) - GWU (I10-6)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    GUU (H15-15) or GUU (I10-4) - Body ground
    10 kΩ or higher
    GVU (H15-14) or GVU (I10-5) - Body ground
    10 kΩ or higher
    GWU (H15-13) or GWU (I10-6) - Body ground
    10 kΩ or higher

  1. Reconnect the inverter connector.

  1. Reconnect the HV control ECU connector.

  1. Reinstall the inverter cover .

  1. Reinstall the service plug grip .



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY