Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A7A-321    Generator Inverter Performance

DTC    P0A7A-323    Generator Inverter Performance

for Preparation Click here


DESCRIPTION

See the description of the inverter .
If the generator inverter has a circuit malfunction, internal short, or overheats, the inverter transmits that information to the GFIV terminal of the HV control ECU via the generator inverter fail signal line.
The HV control ECU monitors the generator inverter fail signal line and detects a malfunction.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A7A
321
+B short in generator inverter fail (GFIV) signal circuit
  1. Wire harness or connector
  2. Inverter with converter assembly
P0A7A
323
Open or GND short in generator inverter fail (GFIV) signal circuit
  1. Wire harness or connector
  2. Inverter with converter assembly

MONITOR DESCRIPTION

The HV control ECU monitors the generator inverter fail (GFIV) signal line. If the HV control ECU detects an open or short malfunction of the GFIV signal circuit, the HV control ECU illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0A7A (INF 321 / 323):
Generator inverter Finv detection
Required sensor / components
Generator Inverter
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TOYOTA's intellectual property
Other conditions belong to TOYOTA's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


Generator inverter fail signal circuit
Open or short

COMPONENT OPERATING RANGE


Generator inverter
DTC P0A7A (INF 321 / 323) is not detected

WIRING DIAGRAM


A092102E16


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from reconnecting it while you are servicing the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes are required to discharge the high-voltage condenser inside the inverter.

1.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER)

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.



    A065744E31
  1. Disconnect the H15 HV control ECU connector.

  1. Remove the inverter cover .



    A092041E42
  1. Disconnect the I10 inverter connector.

  1. Turn the power switch ON (IG).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and inverter cover removed.

  1. Measure the voltage between the terminals of the HV control ECU connector and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    GFIV (H15-35) - Body ground
    Below 1 V
    GINV (H15-23) - Body ground
    Below 1 V

  1. Turn the power switch OFF.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    GFIV (H15-35) - GFIV (I10-22)
    Below 1 Ω
    GINV (H15-23) - GINV (I10-16)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    GFIV (H15-35) or GFIV (I10-22) - Body ground
    10 kΩ or higher
    GINV (H15-23) or GINV (I10-16) - Body ground
    10 kΩ or higher

  1. Reconnect the inverter connector.

  1. Reconnect the HV control ECU connector.

  1. Reinstall the inverter cover .

  1. Reinstall the service plug grip .



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY