Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A7A-520    Generator Inverter Performance

for Preparation Click here


DESCRIPTION

See the description of the inverter .
Upon receiving a generator gate shutdown signal from the HV control ECU, the inverter forcefully stops the operation of the MG1 by turning OFF the power transistors that are actuating the MG1.
The HV control ECU monitors the generator gate shutdown signal and detects a malfunction.

DTC No.
INF Code.
DTC Detection Condition
Trouble Area
P0A7A
520
Generator gate shutdown (GSDN) signal malfunction
  1. Wire harness or connector
  2. HV control ECU

MONITOR DESCRIPTION

The HV control ECU monitors the generator gate shutdown (GSDN) signal. If the HV control ECU detects a fault in the GSDN signal, it illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0A7A (INF 520):
Generator inverter shutdown signal line malfunction
Required sensor / components
Generator inverter
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TOYOTA's intellectual property
Other conditions belong to TOYOTA's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


Actual status of shutdown command signal and its monitoring result
Inconsistent

COMPONENT OPERATING RANGE


Generator inverter
DTC P0A7A (INF 520) is not detected

WIRING DIAGRAM

Refer to DTC P0A7A (INF 342) .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from reconnecting it while you are servicing the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes are required to discharge the high-voltage condenser inside the inverter.

1.READ OUTPUT DTC (HV ECU)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    DTC P0A7A (INF 520) and other DTCs are output

    HINT:
    If any other codes besides P0A7A (INF 520) are output, perform troubleshooting for those DTCs first.



YES
GO TO RELEVANT DTC CHART
NO


2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER)

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.



    A065744E34
  1. Disconnect the H15 HV control ECU connector.

  1. Remove the inverter cover .



    A092041E22
  1. Disconnect the I10 inverter connector.

  1. Turn the power switch ON (IG).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and inverter cover removed.

  1. Measure the voltage between the terminal of the HV control ECU connector and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    GSDN (H15-16) - Body ground
    Below 1 V

  1. Turn the power switch OFF.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    GSDN (H15-16) - GSDN (I10-20)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    GSDN (H15-16) or GSDN (I10-20) - Body ground
    10 kΩ or higher

  1. Reconnect the inverter connector.

  1. Reconnect the HV control ECU connector.

  1. Reinstall the inverter cover .

  1. Reinstall the service plug grip .



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE CONTROL ECU