Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A92-521    Hybrid Generator Performance

for Preparation Click here


DESCRIPTION

See the description of the MG1/MG2 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A92
521
MG1 system malfunction
  1. Hybrid vehicle generator
  2. Inverter with converter assembly

MONITOR DESCRIPTION

The HV control ECU monitors the hybrid vehicle generator (MG1) system. If the HV control ECU detects a malfunction in the MG1 system, it illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0A92 (INF 521):
Generator system malfunction
Required sensor / components
Hybrid vehicle generator, inverter, generator resolver
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TOYOTA's intellectual property
No other condition
-

TYPICAL MALFUNCTION THRESHOLDS


TOYOTA's intellectual property
-

COMPONENT OPERATING RANGE


Hybrid vehicle generator
DTC P0A92 (INF 521) is not detected

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from reconnecting it while you are servicing the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes are required to discharge the high-voltage condenser inside the inverter.

1.READ OUTPUT DTC (HV ECU)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    DTC P0A92 (INF 521) and other DTCs are output

    HINT:
    If any other codes besides P0A92 (INF 521) are output, perform troubleshooting for those DTCs first.



YES
GO TO RELEVANT DTC CHART
NO


2.INSPECT HYBRID VEHICLE GENERATOR ASSEMBLY

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.

  1. Remove the inverter cover .



    A092046E03
  1. Disconnect the three-phase alternating current cable for the hybrid vehicle generator from the inverter.

  1. Using milliohm meter, measure the resistance between the three-phase alternating current cable terminals of the hybrid vehicle generator.

    NOTICE:
    If the generator temperature is too high, the resistance varies considerably, which hinders determining malfunction. Therefore, measure the resistance at a minimum 8 hours after the vehicle has been stopped.

    Standard resistance:
    Tester Connection
    Specified Condition*
    U (I15-1) - V (I15-2)
    Below 109 mΩ at 68°F (20°C)
    V (I15-2) - W (I15-3)
    Below 109 mΩ at 68°F (20°C)
    W (I15-3) - U (I15-1)
    Below 109 mΩ at 68°F (20°C)

    1. *: Apply the formula given below to correct the resistance.
    2. R20 = Rt / {1 + 0.00393 x (T - 20)}
    3. R20: Resistance converted to 68°F (20°C) (mΩ)
    4. Rt: Resistance between measured lines (mΩ)
    5. T: Ambient air temperature during measurement (°C)

  1. Calculate the difference between the maximum and minimum resistance between terminals U - V, V - W, and W - U.

    Standard resistance:
    Below 2 mΩ

  1. Using a megohmmeter, measure the insulation resistance between the three-phase alternating current cable terminals of the hybrid vehicle generator and the body ground.

    Standard resistance:
    Tester Connection
    Specified Condition
    U (I15-1) - Body ground
    10 MΩ or higher
    V (I15-2) - Body ground
    10 MΩ or higher
    W (I15-3) - Body ground
    10 MΩ or higher

  1. Reconnect the three-phase alternating current cable for the hybrid vehicle generator.

  1. Reinstall the inverter cover .

  1. Reinstall the service plug grip .



NG
REPLACE HYBRID VEHICLE GENERATOR ASSEMBLY
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY