Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A90-604    Drive Motor "A" Performance

DTC    P0A90-605    Drive Motor "A" Performance

for Preparation Click here


DESCRIPTION

See the description of the MG1/MG2 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A90
604
MG2 power balance malfunction (small power balance)
  1. Battery current sensor
  2. Hybrid vehicle motor
P0A90
605
MG2 power balance malfunction (large power balance)
  1. Battery current sensor
  2. Hybrid vehicle motor

MONITOR DESCRIPTION

The HV control ECU monitors the energy balance of the hybrid vehicle motor (MG2) system. If the HV control ECU detects a malfunction in the amount of electrical energy while the MG2 charges or discharges electricity, it illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0A90 (INF 604 / 605): Hybrid vehicle motor / Power balance malfunction
Required sensor / components
Hybrid vehicle motor, motor resolver
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TOYOTA's intellectual property
Other conditions belong to TOYOTA's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


Hybrid vehicle motor (power balance)
Small or large

COMPONENT OPERATING RANGE


Hybrid vehicle motor DTC P0A90 (INF 604 / 605) is not detected
DTC P0A90 (INF 604 / 605) is not detected

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from reconnecting it while you are servicing the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes are required to discharge the high-voltage condenser inside the inverter.

1.READ OUTPUT DTC (HV BATTERY)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    DTCs are output



YES
GO TO RELEVANT DTC CHART
NO


2.READ OUTPUT DTC (HV ECU)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    DTC P0A90 (INF 604 or 605) and other DTCs are output

    HINT:
    If any other codes besides P0A90 (INF 604 or 605) are output, perform troubleshooting for those DTCs first.



YES
GO TO RELEVANT DTC CHART
NO


3.INSPECT BATTERY CURRENT SENSOR
A077580E03
  1. Remove the battery current sensor .

  1. Measure the resistance between terminals 1 (VIB) and 2 (GIB).

    Standard resistance:
    Tester Connection
    Specified Condition
    Positive probe to terminal 1 (VIB)
    Negative probe to terminal 2 (GIB)
    3.5 to 4.5 kΩ
    Positive probe to terminal 2 (GIB)
    Negative probe to terminal 1 (VIB)
    5 to 7 kΩ

  1. Measure the resistance between terminals 1 (VIB) and 3 (IB).

    Standard resistance:
    Tester Connection
    Specified Condition
    Positive probe to terminal 1 (VIB)
    Negative probe to terminal 3 (IB)
    3.5 to 4.5 kΩ
    Positive probe to terminal 3 (IB)
    Negative probe to terminal 1 (VIB)
    5 to 7 kΩ

  1. Measure the resistance between terminals 2 (GIB) and 3 (IB).

    Standard resistance:
    0.2 kΩ or less

    NOTICE:
    Even if the probes are changed around, the resistance will not vary.

  1. Reinstall the battery current sensor .



NG
REPLACE BATTERY CURRENT SENSOR
OK

REPLACE HYBRID VEHICLE MOTOR ASSEMBLY