Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > Only Back Door LOCK / UNLOCK Functions do not Operate

for Preparation Click here


DESCRIPTION

The driver side junction block (main body ECU) receives switch signals from the power window regulator master switch and activates the luggage compartment door lock motor according to the signals.

WIRING DIAGRAM


B132159E02


INSPECTION PROCEDURE

1.READ VALUE OF TECHSTREAM (BACK DOOR OPENER SWITCH AND BACK DOOR)
  1. Check the Data List for proper functioning of back door opener switch.

    Main Body ECU:

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    B Dor Open SW
    Back door opener switch signal / ON or OFF
    OK: Back door opener switch is pushed
    OFF: Back door opener switch is not pushed
    -

    OK:
    ON (Back door opener switch is pushed) appears on the screen.

  1. Check the Data List for proper functioning of the back door open judgment.

    Main Body ECU:

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Dor Open
    Back door open judgment / PROHIBT or PERMIT
    PROHIBT: Back door opening is impossible
    PERMIT: Back door opening is possible
    -

    OK:
    PERMIT (Back door can be opened) appears on the screen.

    Result:
    Result
    Proceed to
    NG (back door opener switch)
    A
    NG (back door)
    B
    OK
    C



B
Go to step 4

C
Go to step 5
A


2.INSPECT BACK DOOR LOCK
B075486E01
  1. Remove the back door opener switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pushed (ON)
    Below 1 Ω
    Not pushed (OFF)
    10 kΩ or higher



NG
REPLACE BACK DOOR OPENER SWITCH
OK


3.CHECK WIRE HARNESS (SWITCH - ECU AND BODY GROUND)
B079557E01
  1. Disconnect the L4 switch connector.

  1. Disconnect the B7 ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    L4-2 - B7-12 (BDSU)
    Below 1 Ω
    L4-1 - Body ground



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4.INSPECT BACK DOOR LOCK (DOOR LOCK MOTOR)
B079562E01
  1. Check operation of the back door lock.

    1. Using a screwdriver, move the latch to the full-latch position.

    2. Apply battery voltage to the door lock and check operation the latch.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 3
      Latch turns to open-latch position



NG
REPLACE BACK DOOR LOCK
OK


5.INSPECT BACK DOOR LOCK (COURTESY SWITCH)
B079558E01
  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Open-latch
    Below 1 Ω
    Half-latch
    Full-latch
    10 kΩ or higher
    Over-latch



NG
REPLACE BACK DOOR LOCK
OK


6.CHECK WIRE HARNESS (MOTOR - DRIVE SIDE JUNCTION BLOCK, ECU AND BODY GROUND)

B132160E01

  1. Disconnect the L3 lock connector.

  1. Disconnect the B7 ECU connector.

  1. Disconnect the 1D junction block connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    L3-2 - 1D-7 (BCTY)
    Below 1 Ω
    L3-4 - B7-1 (BACT)
    L3-1 - Body ground
    L3-3 - Body ground



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE DRIVER SIDE JUNCTION BLOCK