Home › SECURITIES › THEFT DETERRENT › THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM > TERMINALS OF ECU



CHECK DRIVER SIDE JUNCTION BLOCK (MAIN BODY ECU)

B129460E01

  1. Disconnect the B6 ECU connector.

  2. Disconnect the 1A, 1B, 1D and 1E junction block connectors.

  3. Measure the resistance and voltage of wire harness side connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (1E-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    ECUB (1A-30) - Body ground
    R - Body ground
    +B (ECUB) power supply
    Always
    10 to 14 V
    ALTB (1B-1) - Body ground
    W - Body ground
    +B (power system, generator system) power supply
    Always
    10 to 14 V
    KSW (1E-23)*1 - Body ground
    Y - Body ground
    Key unlock warning switch input
    No key is in key slot
    10 kΩ or higher
    Key inserted
    Below 1 Ω
    KSW (1E-26)*2 - Body ground
    HCTY (B6-5) - Body ground
    P - Body ground
    Engine hood courtesy switch
    Engine hood closed
    10 kΩ or higher
    Engine hood open
    Below 1 Ω
    DCTY (1D-21) - Body ground
    V - Body ground
    Driver side courtesy switch input
    Driver side door closed
    10 kΩ or higher
    Driver side door open
    Below 1 Ω
    PCTY (1D-24) - Body ground
    BR - Body ground
    Passenger side courtesy switch input
    Passenger side door closed
    10 kΩ or higher
    Passenger side door open
    Below 1 Ω
    RCTY (1D-5) - Body ground
    R - Body ground
    Rear LH side courtesy switch input
    Rear LH side door closed
    10 kΩ or higher
    Rear LH side door open
    Below 1 Ω
    RCTY (1D-20) - Body ground
    R - Body ground
    Rear RH side courtesy switch input
    Rear RH side door closed
    10 kΩ or higher
    Rear RH side door open
    Below 1 Ω
    BCTY (1D-7) - Body ground
    R - Body ground
    Back door courtesy switch
    Back door closed
    10 kΩ or higher
    Back door open
    Below 1 Ω

    HINT:
    *1: with Smart Key System
    *2: without Smart Key System

    If the result is not as specified, there may be a malfunction on the wire harness side.

  4. Reconnect the B6 ECU connector.

  5. Reconnect the 1A, 1B, 1D and 1E junction block connectors.

  6. Measure the voltage of the connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    SIND (B5-8) - Body ground
    R - Body ground
    Security indicator light
    Security indicator light illuminates (illuminates for 30 sec. in alarm sounding state and flashes when immobiliser system is operating)
    3 to 6 V
    SEC (B6-1) - Body ground
    Y - Body ground
    Security horn
    Security horn is sounding (theft deterrent system is in alarm sounding state)
    Pulse generation → Below 1 V
    HAZ (1L- 17) - Body ground
    Y - Body ground
    Hazard light drive
    Answer-back OFF → Answer-back ON
    Pulse generation
    HORN (1A-28) - Body ground
    Y - Body ground
    Vehicle horn (low pitched and high pitched)
    Vehicle horn is sounding (theft deterrent system is in alarm sounding state)
    Pulse generation → Below 1 V
    TRLY (1D-29) - Body ground
    BR - Body ground
    Taillights
    Taillights are flashing (theft deterrent system is in alarm sounding state)
    Pulse generation → Below 1 V
    HRLY (B7-20) - Body ground
    G - Body ground
    Headlights
    Headlights are flashing (theft deterrent system is in alarm sounding state)
    Pulse generation → Below 1 V
    If the result is not as specified, the junction block (body ECU) may have a malfunction.