Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID VEHICLE CONTROL ECU

HYBRID VEHICLE CONTROL ECU > REMOVAL

for Preparation Click here



1. REMOVE REAR NO. 2 FLOOR BOARD


    A088353E01
  1. Unlock the 2 washer tank cover knobs, and then remove the rear floor board.



2. REMOVE REAR DECK FLOOR BOX


    A088354E01
  1. Remove the rear deck floor box from the vehicle.



3. REMOVE REAR NO. 3 FLOOR BOARD


    A088355E02
  1. Detach the 4 claws, and then remove the floor board.



4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



5. REMOVE NO. 1 INSTRUMENT PANEL REGISTER


B074044E02
  1. Detach the 2 claws and 4 clips, and remove the instrument panel register.



6. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL


B074045E02
  1. Remove the 2 screws.

  1. Disconnect the hood lock control cable.

  1. Detach the 4 claws and 5 clips.

  1. Disconnect all connectors and remove the instrument panel finish panel.



7. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL


B074046E02
  1. Detach the 3 claws and 4 clips.

  1. Disconnect the connector and remove the instrument panel finish panel.



8. REMOVE NO. 3 INSTRUMENT PANEL REGISTER


B074047E02
  1. Detach the claw and 5 clips.

  1. Disconnect the connector and remove the instrument panel register.



9. REMOVE NO. 4 INSTRUMENT PANEL REGISTER


B074048E02
  1. Detach the 6 clips and remove the instrument panel register.



10. REMOVE NO. 2 INSTRUMENT PANEL REGISTER


B074049E02
  1. Detach the 2 claws and 4 clips, and remove the instrument panel register.



11. REMOVE MULTI-DISPLAY ASSEMBLY


    I039616E01
  1. Remove the 2 bolts.

  1. Disconnect the connector and remove the multi-display.



12. REMOVE GLOVE COMPARTMENT DOOR STOPPER


B074050E01
  1. Holding the part indicated in the illustration, remove the glove compartment door stopper from the glove compartment door.



13. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


B074051E02
  1. While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, open the door to release it from the 2 stoppers.

  1. Open the door until it is horizontal.



    B074052E02
  1. Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.



14. REMOVE GLOVE COMPARTMENT DOOR


B074053E02
  1. Remove the 2 screws.

  1. Detach the claw and 2 clips, and remove the glove compartment door.



15. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL


16. REMOVE FRONT PILLAR GARNISH CORNER PIECE RH


17. REMOVE FRONT PILLAR GARNISH CORNER PIECE LH


18. REMOVE FRONT PILLAR GARNISH RH


19. REMOVE FRONT PILLAR GARNISH LH


20. DISCONNECT AIRBAG CONNECTOR


21. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
  1. Remove the 3 screws.

  1. Remove the 2 bolts.

  1. Pull up the instrument panel to detach the 6 claws and 3 clips.



  1. Remove the instrument panel.


    B075862E02



22. REMOVE NO. 3 HEATER TO REGISTER DUCT


    I038566E01
  1. Remove the clip and No. 3 heater to register duct with the No. 2 side defroster nozzle duct.



23. REMOVE ECM


A087532E01
  1. Disconnect the 4 ECM connectors.

  1. Disconnect the 4 hybrid vehicle control ECU connectors.



    A087535E01
  1. Remove the 2 nuts and bolt, and ECM with bracket.



    A087475E01
  1. Remove the 2 nuts and ECM.



    A087476E01
  1. Remove the 6 screws and 3 No. 1 ECM brackets.



    A087477E01
  1. Remove the 4 screws and 2 No. 2 ECM brackets.



    A087478E01
  1. Remove the 2 screws and No. 3 ECM bracket.



24. REMOVE HYBRID VEHICLE CONTROL ECU


    A077552E01
  1. Remove the 2 nuts and hybrid vehicle control ECU.