Home › HYBRID SYSTEM › P112 HYBRID BATTERY CONTROL › BATTERY CURRENT SENSOR

BATTERY CURRENT SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL BATTERY CURRENT SENSOR


A083564E01

CAUTION:
Wear insulating gloves.

  1. Install the battery current sensor with the 2 screws.

    Torque:
    1.4 N*m{ 14 kgf*cm , 12 in.*lbf }

  1. Connect the connector.



    A083638E01
  1. Install the main battery cable with a new nut.

    Torque:
    5.6 N*m{ 57 kgf*cm , 50 in.*lbf }



    A083579E02
  1. Install the terminal cover.



2. INSTALL NO. 6 BATTERY CARRIER PANEL


    A083532E01
  1. Install the battery carrier panel with the bolt and 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



3. INSTALL BATTERY CARRIER BRACKET


    A083527E01
  1. Install the battery carrier bracket with the 7 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 in.*lbf }



4. INSTALL DECK TRIM SIDE PANEL LH
  1. Connect the lighting connector.



    A083537E03
  1. Install the deck trim side panel with the 8 clips and 2 bolts, and then install the part of the weather strip.

  1. Install the luggage hold belt striker with the bolt.



5. INSTALL DECK FLOOR BOX LH


    A083541E01
  1. Install the deck floor box with the clip.



6. INSTALL REAR NO. 4 FLOOR BOARD


A083542E04


7. INSTALL REAR SIDE SEAT BACK FRAME LH


    A083540E04
  1. Install the seat back frame with the bolt.



8. INSTALL REAR NO. 1 FLOOR BOARD


A083543E03
  1. Install the floor board.

  1. Install the 2 luggage strikers with the 2 bolts.



9. INSTALL REAR SEAT CUSHION ASSEMBLY


A083593E03


10. INSTALL TONNEAU COVER


A083594E01


11. INSTALL REAR DECK TRIM COVER


A083536E03


12. INSTALL SERVICE PLUG GRIP

CAUTION:
Wear insulating gloves.

  1. Joint the service plug grip with the HV battery.

  1. While pushing the service plug grip to the right, rotate the lever to the right.

  1. Slide the lever down to lock the service plug grip in place.

    NOTICE:
    1. The service plug grip must be locked. If not, it may cause DTCs to output.

    2. Do not operate the power switch when the service plug grip is not properly locked. It may damage the hybrid vehicle control ECU in rare cases.


      A089219



13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
  1. When the warning light is illuminated or the battery has been disconnected and reconnected, turning the power switch may not start the system on the first try. If so, turn the power switch again.
  2. With the power switch's power mode changed to ON (IG), disconnect the battery. If the key is not in the key slot during reconnection, DTC B2799 may be output.



    A088356E01
  1. Connect the battery negative cable, and then tighten the nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



14. INSTALL REAR NO. 3 FLOOR BOARD


    A088355E02
  1. Install the floor board, and then attach the 4 claws.



15. INSTALL REAR DECK FLOOR BOX


    A088354E01
  1. Install the rear deck floor box to the vehicle.



16. INSTALL REAR NO. 2 FLOOR BOARD


    A088353E01
  1. Install the floor board, and then lock the 2 cover knobs.



17. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.