Home › HYBRID SYSTEM › P112 HYBRID BATTERY CONTROL › BATTERY CURRENT SENSOR

BATTERY CURRENT SENSOR > REMOVAL

for Preparation Click here


CAUTION:
  1. When working on the high voltage systems, always wear insulating gloves.
  2. Keep the removed service plug in your pocket to prevent other technicians from reconnecting it while you are servicing the vehicle.
  3. After removing the service plug grip, do not touch the high voltage connectors and terminals for 5 minutes.

NOTICE:
After removing the service plug grip, do not operate the power switch as it may damage the hybrid vehicle control ECU.



1. PRECAUTION

CAUTION:
The hybrid system uses high voltage circuits, so improper handling could cause an electric shock or leakage. During service (including installation/removal, inspection and replacement of parts), be sure to follow the procedures (Click here).



2. REMOVE REAR NO. 2 FLOOR BOARD


    A088353E01
  1. Unlock the 2 washer tank cover knobs, and then remove the rear floor board.



3. REMOVE REAR DECK FLOOR BOX


    A088354E01
  1. Remove the rear deck floor box from the vehicle.



4. REMOVE REAR NO. 3 FLOOR BOARD


    A088355E02
  1. Detach the 4 claws, and then remove the floor board.



5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



6. REMOVE SERVICE PLUG GRIP


A083545E03

CAUTION:
Wear insulating gloves.

  1. Slide up the lever of the service plug grip. Remove the service plug grip while turning the lever to the left.

  1. Insulate the service plug with insulating tape.



7. REMOVE REAR DECK TRIM COVER


    A083536E03
  1. Detach the 4 clips shown in the illustration, then remove the deck trim cover.



8. REMOVE TONNEAU COVER


    A083594E01
  1. Remove the tonneau cover from the vehicle.



9. REMOVE REAR SEAT CUSHION ASSEMBLY


    A083593E03
  1. Undo the 2 joints shown in the illustration, then remove the rear seat cushion.



10. REMOVE REAR NO. 1 FLOOR BOARD


    A083543E03
  1. Remove the 2 bolts and luggage hold belt strikers.

  1. Remove the 5 clips shown in the illustration and the rear floor board.



11. REMOVE REAR SIDE SEAT BACK FRAME LH


    A083540E04
  1. Remove the bolt from the rear side seat back frame LH.

  1. Undo the 3 joints, then remove the rear side seat back frame LH.



12. REMOVE REAR NO. 4 FLOOR BOARD


    A083542E03
  1. While lifting up the rear floor board as shown in the illustration, undo the 2 joints and remove the rear floor board.



13. REMOVE DECK FLOOR BOX LH


    A083541E01
  1. Remove the clip and deck floor box LH.



14. REMOVE DECK TRIM SIDE PANEL LH
  1. Remove the bolt and luggage hold belt striker.



    A083537E03
  1. Remove the 2 bolts from the deck trim side panel LH.

  1. Remove the clip from the deck trim side panel LH.

  1. Undo the 8 clips, then pull out a part of the weather strip and remove the deck trim side panel LH.

  1. Disconnect the lighting connector.



15. REMOVE BATTERY CARRIER BRACKET


    A083527E01
  1. Remove the 7 bolts and battery carrier bracket.



16. REMOVE NO. 6 BATTERY CARRIER PANEL


    A083532E01
  1. Remove the 3 bolts, 2 nuts and battery carrier panel.



17. REMOVE BATTERY CURRENT SENSOR


A083579E01

CAUTION:
Wear insulating gloves.

  1. Remove the terminal cover.



    A083638E01
  1. Remove the nut, then disconnect the main battery cable.



    A083564E01
  1. Disconnect the connector.

  1. Remove the 2 screws and battery current sensor.