Home › COMMUNICATION SYSTEM › MULTIPLEX COMMUNICATION › MULTIPLEX COMMUNICATION SYSTEM

MULTIPLEX COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK GATEWAY ECU

B126164E01

  1. Disconnect the G1 connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    BATT (G1-10) - Body ground
    Y - Body ground
    +B (BATT) power supply
    Always
    10 to 14 V
    IG (G1-1) - Body ground
    B - Body ground
    Ignition power supply
    Power switch ON (IG)
    10 to 14 V
    ACC (G1-2) - Body ground
    P - Body ground
    ACC power supply
    Power switch ON (ACC)
    10 to 14 V
    SIL (G1-7) - Body ground
    W - Body ground
    Bus "+" line
    During transmission
    Pulse generation
    MPD2 (G1-12) - Body ground
    GR - Body ground
    BEAN line
    Always
    10 kΩ or higher
    MPD1 (G1-3) - Body ground
    GR - Body ground
    BEAN line
    Always
    10 kΩ or higher
    GTX+ (G1-6) - Body ground
    B - Body ground
    AVC-LAN line
    Always
    10 kΩ or higher
    GTX- (G1-21) - Body ground
    W - Body ground
    AVC-LAN line
    Always
    10 kΩ or higher
    GND (G1-24) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK A/C ECU

B133133E01

  1. Disconnect the A8 connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    +B (A8-6) - Body ground
    Y - Body ground
    +B power supply
    Always
    10 to 14 V
    MPX+ (A8-3) - Body ground
    B - Body ground
    BEAN line
    Always
    10 kΩ or higher
    MPX2+ (A8-11) - Body ground
    GR - Body ground
    BEAN line
    Always
    10 kΩ or higher
    GND (A8-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK DRIVER SIDE JUNCTION BLOCK (MAIN BODY ECU)

B126166E02

  1. Disconnect the B5 ECU connector.

  2. Disconnect the 1A, 1E and 1G junction block connectors.

  3. Measure the voltage and resistance of the wire harness side connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    ECUB (1A-30) - Body ground
    R - Body ground
    +B (ECUB) power supply
    Always
    10 to 14 V
    MPX1 (1G-9) - Body ground
    GR - Body ground
    BEAN line
    Always
    10 kΩ or higher
    MPX2 (B5-15) - Body ground
    B - Body ground
    BEAN line
    Always
    10 kΩ or higher
    GND (1E-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK TRANSPONDER KEY ECU

B126056E01

  1. Disconnect the T5 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    IG (T5-4) - Body ground
    O - Body ground
    +B (IG) power supply
    Always
    10 to 14 V
    MPX1 (T5-17) - Body ground
    B - Body ground
    BEAN line
    Always
    10 kΩ or higher
    MPX2 (T5-16) - Body ground
    GR - Body ground
    BEAN line
    Always
    10 kΩ or higher
    GND (T5-22) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK TRANSMISSION CONTROL ECU

B126167E01

  1. Disconnect the T4 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    +B (T4-1) - Body ground
    L - Body ground
    +B power supply
    Always
    10 to 14 V
    MPX1 (T4-19) - Body ground
    GR - Body ground
    BEAN line
    Always
    10 kΩ or higher
    MPX2 (T4-18) - Body ground
    B - Body ground
    BEAN line
    Always
    10 kΩ or higher
    E1 (T4-15) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK CERTIFICATION ECU (WITH SMART KEY)

B126057E01

  1. Disconnect the S11 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    +B1 (S11-1) - Body ground
    R - Body ground
    +B power supply
    Always
    10 to 14 V
    MPX1 (S11-31) - Body ground
    GR - Body ground
    BEAN line
    Always
    10 kΩ or higher
    MPX2 (S11-32) - Body ground
    B - Body ground
    BEAN line
    Always
    10 kΩ or higher
    E (S11-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK COMBINATION METER

B126168E01

  1. Disconnect the C10 meter connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    +B (C10-21) - Body ground
    Y - Body ground
    +B power supply
    Always
    10 to 14 V
    MPX+ (C10-24) - Body ground
    B - Body ground
    BEAN line
    Always
    10 kΩ or higher
    MPX- (C10-25) - Body ground
    GR - Body ground
    BEAN line
    Always
    10 kΩ or higher
    SE (C10-14) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK POWER SOURCE CONTROL ECU

B126057E02

  1. Disconnect the P6 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AM1 (P6-33) - Body ground
    R - Body ground
    +B (AM1) power supply
    Always
    10 to 14 V
    MPX1 (P6-7) - Body ground
    GR - Body ground
    BEAN line
    Always
    10 kΩ or higher
    MPX2 (P6-24) - Body ground
    B - Body ground
    BEAN line
    Always
    10 kΩ or higher
    GND2 (P6-6) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK TIRE PRESSURE MONITOR ECU

C107243E03

  1. Disconnect the T11 ECU connector.

  2. Measure the resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    IG (T11-1) - Body ground
    B - Body ground
    Power supply
    Always
    10 to 14 V
    MPX1 (T11-6) - Body ground
    W - Body ground
    BEAN line
    Always
    10 kΩ or higher
    MPX2 (T11-12) - Body ground
    B - Body ground
    BEAN line
    Always
    10 kΩ or higher
    GND (T11-7) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.