Home › ENGINE › 1NZ-FXE COOLING › FAN

FAN > INSTALLATION

for Preparation Click here



1. INSTALL COOLING FAN MOTOR


    A128250
  1. Install the fan motor with the 3 bolts.

    Torque:
    3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



2. INSTALL NO. 2 COOLING FAN MOTOR
  1. Install the fan motor with the 3 bolts.

    Torque:
    3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



3. INSTALL FAN
  1. Install the fan with the nut.

    Torque:
    6.2 N*m{ 63 kgf*cm , 55 in.*lbf }



4. INSTALL NO. 2 FAN
  1. Install the fan with the nut.

    Torque:
    6.2 N*m{ 63 kgf*cm , 55 in.*lbf }



5. INSTALL FAN WITH MOTOR ASSEMBLY


A086930E01
  1. Set the fan with motor to the vehicle, then install it with the 4 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    A086929E01
  1. Connect the 2 wire harness clamps shown in the illustration.



    A086928E01
  1. Install the hood lock control cable to the radiator support.

  1. Install the radiator support with the 5 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    A092969E01
  1. Connect the hood lock control cable to the hood lock.

  1. Install the hood lock with the 3 bolts .



    A086926E01
  1. Connect the horn connector shown in the illustration.



    A092519E01
  1. Install the cooler bracket with the 2 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt A

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf } for bolt B



    A089867E01
  1. Install the inverter bracket with the 3 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf } for bolt A

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf } for bolt B



    A086923E01
  1. Connect the connector and install the clamp.

  1. Connect the radiator inlet hose.



    A086922E01
  1. Connect the inverter reservoir hose to each clamp.



    A086921E01
  1. Connect the radiator reservoir hose.

  1. Connect the radiator outlet hose.



    A086920E01
  1. Connect the hose shown in the illustration.



    A086919E01
  1. Connect the connector shown in the illustration.



    A086918E01
  1. Install the 2 hose clamps to the fan shroud.

  1. Connect the hose shown in the illustration.



    A086917E01
  1. Install the hose clamp to the fan shroud.

  1. Connect the hose and connector shown in the illustration.



6. INSTALL FRONT BUMPER COVER


    B132997E01
  1. Put protective tape under the front fender.

  1. w/ Fog light:
    Connect the 2 fog light connectors.

  1. Attach the 12 claws to install the bumper cover.

  1. Install the 4 screws and 3 clips.

  1. Install the 2 radiator grille protectors.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



7. CONNECT CABLE TO BATTERY NEGATIVE TERMINAL


8. INSTALL REAR NO. 3 FLOOR BOARD


    A088355E02
  1. Install the floor board, and then attach the 4 claws.



9. INSTALL REAR DECK FLOOR BOX


    A088354E01
  1. Install the rear deck floor box to the vehicle.



10. INSTALL REAR NO. 2 FLOOR BOARD


    A088353E01
  1. Install the floor board, and then lock the 2 cover knobs.



11. ADD ENGINE COOLANT (for Engine)
  1. Fill the radiator on the hybrid side with coolant .

  1. Fill the radiator on the engine side with coolant .



12. INSPECT FOR COOLANT LEAK (for Engine)
  1. Check the cooling system on the hybrid side for coolant leaks.

  1. Check the cooling system on the engine side for coolant leaks .



13. INSTALL ENGINE UNDER COVER RH


14. INSTALL ENGINE UNDER COVER LH


15. INSTALL RADIATOR SUPPORT OPENING COVER


    A088174E01
  1. Install the opening cover with the 6 clips.



16. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting the cable from the negative (-) battery terminal.