Home › ENGINE › 1NZ-FXE COOLING › FAN

FAN > REMOVAL

for Preparation Click here



1. REMOVE REAR NO. 2 FLOOR BOARD


    A088353E01
  1. Unlock the 2 washer tank cover knobs, and then remove the rear floor board.



2. REMOVE REAR DECK FLOOR BOX


    A088354E01
  1. Remove the rear deck floor box from the vehicle.



3. REMOVE REAR NO. 3 FLOOR BOARD


    A088355E02
  1. Detach the 4 claws, and then remove the floor board.



4. DISCONNECT CABLE FROM BATTERY NEGATIVE TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



5. REMOVE RADIATOR SUPPORT OPENING COVER


    A088174E01
  1. Remove the 6 clips and radiator support opening cover.



6. REMOVE ENGINE UNDER COVER LH


7. REMOVE ENGINE UNDER COVER RH


8. DRAIN ENGINE COOLANT (for Engine)
  1. Drain the coolant in the radiator on the engine side .

  1. After draining the coolant in the radiator on the engine side, remove the radiator drain cock plug.

  1. Drain the coolant in the radiator on the hybrid side .



9. REMOVE FRONT BUMPER COVER


B130316E01
  1. Put protective tape under the front fender.

  1. Using a clip remover, remove the 3 clips.

  1. Remove the 2 radiator grille protectors and 4 screws.

  1. Detach the 8 claws.



    B078079E02
  1. Detach the 4 claws and remove the bumper cover.

    1. Hold the front bumper cover on its upper and lower parts with your hands as shown in the illustration.

    2. Pull up the front bumper cover's lower part while holding its upper part securely.

      NOTICE:
      1. The claw will not disengage unless the front bumper cover's upper part is securely held.
      2. Do not forcibly pull up the front bumper. This will deform the claw.

  1. w/ Fog light:
    Disconnect the 2 fog light connectors.



10. REMOVE FAN WITH MOTOR ASSEMBLY


    A086917E01
  1. Disconnect the connector and hose shown in the illustration.

  1. After disconnecting the hose, remove the hose clamp.



    A086918E01
  1. Disconnect the hose shown in the illustration.

  1. After disconnecting the hose, remove the 2 hose clamps.



    A086919E01
  1. Disconnect the connector shown in the illustration.



    A086920E01
  1. Disconnect the hose shown in the illustration.



    A086921E01
  1. Disconnect the radiator outlet hose.

  1. Disconnect the radiator reservoir hose.



    A086922E01
  1. Disconnect the inverter reservoir hose from the clamps.



    A086923E01
  1. Disconnect the radiator inlet hose.

  1. Disconnect the connector and remove the clamp shown in the illustration.



    A086924E01
  1. Remove the 3 bolts and inverter bracket.



    A086925E01
  1. Remove the 2 bolts and cooler bracket.



    A086926E01
  1. Disconnect the horn connector shown in the illustration.



    A086927E01
  1. Remove the 3 bolts, disconnect the hood lock control cable, and then remove the hood lock.



    A086928E01
  1. Remove the 5 bolts and radiator support.

  1. Remove the hood lock control cable from the radiator support.



    A086929E01
  1. Disconnect the wire harness clamps shown in the illustration.



    A086930E01
  1. Remove the 4 bolts, then remove the fan with motor from the vehicle.



11. REMOVE FAN


    A128250
  1. Remove the nut and fan.



12. REMOVE NO. 2 FAN
  1. Remove the nut and fan.



13. REMOVE COOLING FAN MOTOR
  1. Remove the 3 bolts and fan motor.



14. REMOVE NO. 2 COOLING FAN MOTOR
  1. Remove the 3 bolts and fan motor.