WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Key System) > TERMINALS OF ECU |
| CHECK DRIVER SIDE JUNCTION BLOCK (MAIN BODY ECU) |

Disconnect the 1A, 1B, 1D, 1E and 1J junction block connectors.
Measure the resistance and voltage of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| GND (1E-17) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| SIG (1B-1) - Body ground | W - Body ground | Ignition power supply | Power switch OFF | Below 1 V |
| Power switch ON (IG) | 10 to 14 V | |||
| ACC (1J-5) - Body ground | G - Body ground | Ignition power supply | Power switch OFF | Below 1 V |
| Power switch ON (ACC) | 10 to 14 V | |||
| ECUB (1A-30) - Body ground | R - Body ground | +B (ECUB) power supply | Always | 10 to 14 V |
| KSW (1E-23) - Body ground | Y - Body ground | Key unlock warning switch input | No key in key slot | 10 kΩ or higher |
| Key inserted | Below 1 Ω | |||
| KSW (1E-26) - Body ground | No key in key slot | 10 kΩ or higher | ||
| Key inserted | Below 1 Ω | |||
| DCTY (1D-21) - Body ground | V - Body ground | Driver side door courtesy switch input | Driver side door closed | 10 kΩ or higher |
| Driver side door open | Below 1 Ω | |||
| PCTY (1D-24) - Body ground | BR - Body ground | Passenger side door courtesy switch input | Passenger side door closed | 10 kΩ or higher |
| Passenger side door open | Below 1 Ω | |||
| BCTY (1D-7) - Body ground | R- Body ground | Back door courtesy switch input | Back door closed | 10 kΩ or higher |
| Back door open | Below 1 Ω |
Reconnect the 1A, 1B, 1D, 1E and 1J junction block connectors.
Measure the voltage of the connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| HAZ (1L-17) - Body ground | Y - Body ground | Hazard warning light drive | Answer-back OFF | Below 1 V |
| Answer-back ON | Pulse generation | |||
| RDA (B7-23) - Body ground | L- Body ground | Door control receiver input | Transmitter switch OFF (power switch OFF and all door closed) | Below 1 V |
| Transmitter switch ON (power switch OFF and all door closed) | Pulse generation |
| CHECK CERTIFICATION ECU |

Disconnect the S11 ECU connector.
Measure the resistance and voltage of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E (S11-17) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| +B1 (S11-1) - E (S11-17) | R - W-B | Battery power supply | Always | 10 to 14 V |
| IG (S11-18) - E (S11-17) | B - W-B | Ignition power supply | Power switch OFF | Below 1 V |
| Power switch ON (IG) | 10 to 14 V |
Reconnect the S11 ECU connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| RSSI (S11-11) - E (S11-17) | V - W-B | Door control receiver output signal | Transmitter switch OFF (power switch OFF and all doors closed) | 5 to 0 V |
| Transmitter switch ON (power switch OFF and all doors closed) | Below 1 V | |||
| RDA (S11-10) - E (S11-17) | GR - W-B | Door control receiver input signal | Transmitter switch OFF (power switch OFF and all doors closed) | Below 1 V |
| Transmitter switch ON (power switch OFF and all doors closed) | Alternating between 6 to 7 V and below 1 V | |||
| CLG1 (S11-13) - E (S11-17) | P - W-B | Driver door oscillator sensor signal | Power switch OFF (all doors open with key from outside vehicle) | Pulse generation |
| Power switch ON (IG) (all doors open with key from outside vehicle) | No pulse | |||
| SEL1 (S11-23) - E (S11-17) | Y - W-B | Driver door oscillator sensor signal | Key placed at least 3 m (9.84 ft.) from driver door | 10 to 14 V |
| Place key close to front door outside handle RH | Below 1 V |