Home › ENGINE › 1NZ-FXE FUEL › FUEL TANK

FUEL TANK > INSTALLATION

for Preparation Click here



1. INSTALL NO. 1 FUEL TANK CUSHION


A132605
  1. Install 9 new cushions to the fuel tank.



2. INSTALL NO. 1 FUEL TUBE CLAMP


    A087501E01
  1. Install the 2 clamps to the fuel tank.



3. INSTALL FUEL TANK RETAINER LH


A087505E02
  1. Install a new gasket to the fuel tank.

  1. While being careful that the gasket does not drop in the fuel tank, insert the fuel tank retainer LH into the fuel tank so the protrusion of the fuel tank retainer LH is in the middle of the 2 convex pats of the fuel tank.



4. INSTALL FUEL TANK PRESSURE SENSOR


A087506E02
  1. Push the fuel tank pressure sensor to the plug of the fuel tank retainer LH, and then install the tube joint clip.

    NOTICE:
    1. Check that there are no scratches or foreign objects around the connected part of the fuel tank pressure sensor and fuel tank retainer LH before this procedure.
    2. Check that the fuel tank pressure sensor is securely inserted to the end.
    3. Check that the tube joint clip is on the collar of the fuel tank pressure sensor.
    4. After installing the tube joint clip, check that the fuel tank pressure sensor cannot be pulled out.



5. INSTALL CANISTER


    A087498E01
  1. Install the nut to the fuel tank.



    A087497E01
  1. Install the canister with the bolt and 2 nuts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Connect the No. 1 canister outlet hose to the fuel tank.

  1. Connect the canister hose to the fuel tank retainer.



6. INSTALL FUEL TANK WIRE


A087496E05
  1. Install the 3 wire harness clamps as shown in the illustration D.

  1. Connect the vapor pressure sensor connector as shown in the illustration C.

  1. Connect the VSV connector as shown in the illustration B.

  1. Install the clamp as shown in the illustration A.



7. INSTALL FUEL TANK VENT HOSE


A114372E02
  1. Align the fuel tank vent hose connector with the pipe, then push in the fuel tank vent hose connector until the retainer makes a "click" sound to install the fuel tank vent hose to the trap canister with pump module.

    NOTICE:
    1. Check that there are no scratches or foreign objects around the connected part of the fuel tank vent hose connector and pipe before this procedure.
    2. After connecting the fuel tank vent hose, check that the fuel tank vent hose is securely connected by pulling the fuel tank vent hose connector.



8. INSTALL TRAP CANISTER WITH PUMP MODULE


A087504E01
  1. Install a new gasket to the fuel tank.

  1. Insert the trap canister with pump module into the fuel tank.

    NOTICE:
    Be careful that the gasket does not drop in the fuel tank.



    A128672
  1. Install the 2 clamps to the trap canister with pump module.



    A114371
  1. Install the trap canister with pump module and connect the ground terminal of the fuel tank wire with the 2 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Install the fuel tank vent hose to the 2 fuel tube clamps.

  1. Install the clamp to the fuel tank vent hose and canister hose.

  1. Connect the VSV connector.



9. INSTALL FUEL TANK TO CANISTER TUBE


    A114370
  1. Install the fuel tank to canister tube to the canister's hose.

  1. Connect the fuel tank to canister tube to the 2 No. 1 fuel tube clamps.



10. INSTALL FUEL SUCTION TUBE SUB-ASSEMBLY


A114373E01
  1. Align the suction tube connector with the pipe, and then push in the suction tube connector until the retainer makes a "click" sound to install the fuel suction tube to the pipe.

    NOTICE:
    1. Check that there are no scratches or foreign objects around the connected part of the quick connector and pipe before this procedure.
    2. After connecting the fuel suction tube, check that the fuel suction tube is securely connected by pulling the suction tube connector.

  1. Connect the fuel suction tube to the 2 No. 1 fuel tube clamps.



11. INSTALL NO. 2 FUEL TANK MAIN TUBE SUB-ASSEMBLY


A114374E01
  1. Align the main tube connector with the pipe, and then push in the main tube connector until the retainer makes a "click" sound to install the No. 2 fuel tank main tube to the pipe.

    NOTICE:
    1. Check that there are no scratches or foreign objects around the connected part of the fuel tube connector.
    2. After connecting the No. 2 fuel tank main tube, check that the No. 2 fuel tank main tube is securely connected by pulling the main tube connector.

  1. Install the checker to the pipe.

  1. Connect the No. 2 fuel tank main tube to the clamp.



    A114369
  1. Connect the connector clamp to the rear fuel tank bracket.

  1. Install the rear fuel tank bracket with the 3 nuts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



12. INSTALL FUEL TANK ASSEMBLY
  1. Set the fuel tank to a transmission jack.

  1. Operate the transmission jack, and then install the fuel tank to the vehicle.

  1. Operate the transmission jack, and then connect the fuel tank inlet pipe.



    A087489E02
  1. Install the No. 1 fuel tank band RH and LH with the 4 bolts.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

  1. Install the fuel tube connector and fuel filler pipe clamp to the fuel tank inlet pipe.



    A087510E01
  1. Connect the No. 1 canister tube.

    1. Align the No. 1 canister tube connector with the pipe, and then push in the No. 1 canister tube connector until the retainer makes a "click" sound to connect the No. 1 canister tube to the fuel tank to filler pipe.

      NOTICE:
      1. Check that there are no scratches or foreign objects around the connected part of the No. 1 canister tube connector and pipe before this procedure.
      2. After connecting the No. 1 canister tube, check that the No. 1 canister tube is securely connected by pulling the No. 1 canister tube connector.



    A087511E01
  1. Connect the fuel suction tube.

    1. Align the suction tube connector with the pipe, and then push in the suction tube connector until the retainer makes a "click" sound to connect the fuel suction tube to the fuel tank to filler pipe.

      NOTICE:
      1. Check that there are no scratches or foreign objects around the connected part of the suction tube connector and pipe before this procedure.
      2. After connecting the fuel suction tube, check that the fuel suction tube is securely connected by pulling the suction tube connector.



    A087512E01
  1. Connect the fuel tank vent hose.

    1. Align the fuel tank vent hose connector with the pipe, and then push in the fuel tank vent hose connector until the retainer makes a "click" sound to connect the fuel tank vent hose to the canister filter.

      NOTICE:
      1. Check that there are no scratches or foreign objects around the connected part of the fuel tank vent hose connector and pipe before this procedure.
      2. After connecting the fuel tank vent hose, check that the fuel tank vent hose is securely connected by pulling the vent hose connector.



    A091721E02
  1. Connect the No. 2 fuel tank main tube.

    1. Align the fuel tube connector with the pipe, and then push in the fuel tube connector until the retainer makes a "click" sound to connect the No. 2 fuel tank main tube to the pipe.

      NOTICE:
      1. Check that there are no scratches or foreign objects around the connected part of the fuel tube connector and pipe before this procedure.
      2. After connecting the No. 2 fuel tank main tube, check that the No. 2 fuel tank main tube is securely connected by pulling the quick connector.

  1. Install the checker to the pipe.



    A087603E02
  1. Connect the fuel tank to canister tube.

    1. Align the fuel tank to canister tube connector with the pipe, and then push in the fuel tank to canister tube connector until the retainer makes a "click" sound to connect the fuel tank to canister tube to the pipe.

      NOTICE:
      1. Check that there are no scratches or foreign objects around the connected part of the fuel tank to canister tube connector and pipe before this procedure.
      2. After connecting the fuel tank to canister tube, check that the fuel tank to canister tube is securely connected by pulling the quick connector.



13. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A111834
  1. Using a vernier caliper, measure the free length of the compression spring.

    Minimum length:
    40.5 mm (1.594 in.)

    If the length is less than the minimum, replace the compression spring.



    A076194E04
  1. Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the exhaust manifold.

    NOTICE:
    1. Tap in the gasket in the correct direction.
    2. Do not reuse the removed gasket.
    3. Do not push in the gasket while installing the exhaust pipe.

  1. Connect the 2 exhaust pipe supports, and install the exhaust pipe.

  1. Install the 2 compression springs and 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


15. INSPECT FOR FUEL LEAK
  1. Check that there are no leaks in the fuel system while fuel pressure is applied.



16. INSPECT FOR EXHAUST GAS LEAK


17. INSTALL FRONT FLOOR PANEL BRACE


    A086201
  1. Install the floor panel brace with the 2 bolts.

    Torque:
    30 N*m{ 302 kgf*cm , 22 ft.*lbf }



18. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER


B074061E03
  1. Attach the 4 claws and 2 clips to install the instrument panel finish panel.

  1. Install the clip.



19. INSTALL REAR FLOOR SERVICE HOLE COVER


A087515E02
  1. Attach new butyl tape to the rear floor service hole cover.

  1. Connect the wire to wire connector.

  1. Connect the fuel pump connector.

  1. Install the rear floor service hole cover while adjusting it to the 3 convex parts of the floor panel.

    NOTICE:
    Be careful that the rear floor service hole cover does not overlap the convex parts of the floor panel when installing.



20. INSTALL REAR SEAT CUSHION ASSEMBLY

NOTICE:
When installing the seat cushion, make sure the seat belt buckle is not under the seat cushion.



    B132601E01
  1. Attach the seat cushion's rear hook to the center hinge.

  1. Insert the inner belts through the slits on the seat cushion.



    B132602
  1. Attach the seat cushion's 2 front hooks to the vehicle body.

  1. Confirm that the seat cushion is firmly installed.



21. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.