Home › ENGINE › 1NZ-FXE FUEL › FUEL TANK

FUEL TANK > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. The DISCHARGE FUEL SYSTEM PRESSURE procedures must be performed before disconnecting any part of the fuel system.
  2. After performing the DISCHARGE FUEL SYSTEM PRESSURE procedures, pressure will remain in the fuel line. When disconnecting the fuel line, place a cloth or equivalent over fittings to reduce the risk of fuel spray.

  1. Remove the integration relay (unit C: C/OPN relay) from the engine room junction block.

  1. Start the engine. After the engine has stopped, turn the power switch off.

    HINT:
    DTC P0171 (system too lean) may be set.

  1. Check that the engine does not start.

  1. Remove the fuel tank cap, and let the air out of the fuel tank.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  1. Install the integration relay (unit C: C/OPN relay) to the engine room junction block.



2. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER


B074061E02
  1. Using a clip remover, remove the clip from the instrument panel finish panel lower center.

  1. Detach the 4 claws and 2 clips, and remove the instrument panel finish panel.



3. REMOVE FRONT FLOOR PANEL BRACE


    A086201
  1. Remove the 2 bolts and floor panel brace.



4. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.

  1. Remove the front exhaust pipe from the 2 exhaust pipe supports.



  1. Remove the gasket from the exhaust manifold.


    A086203



5. REMOVE REAR SEAT CUSHION ASSEMBLY


    B132600E01
  1. Detach the seat cushion's 2 front hooks from the vehicle body.

    NOTICE:
    Follow the instructions below carefully as the cushion frame deforms easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat for the other hook.

  1. Detach the seat cushion's rear hook.

  1. Remove the seat cushion.



6. REMOVE REAR FLOOR SERVICE HOLE COVER


    A087483E02
  1. Remove the butyl tape and rear floor service hole cover.

  1. Disconnect the fuel pump connector.

  1. Disconnect the wire to wire connector.



7. REMOVE FUEL TANK ASSEMBLY


    A112310E01
  1. Disconnect the fuel tank from the canister tube.

    1. Pinch the retainer of the fuel tube connector, then pull out the fuel tube connector to disconnect the fuel tank to canister tube from the pipe.

      NOTICE:
      1. Remove dirt or foreign objects on the fuel tube connector before this procedure.
      2. Do not allow any scratches or foreign objects on the parts when disconnecting them as the fuel tube connector has the O-ring that seals the pipe.
      3. Perform this work by hand. Do not use any tools.
      4. Do not forcibly bend, kink or twist the nylon tube.
      5. Protect the connecting part by covering it with a plastic bag after disconnecting the fuel tank from the canister tube.
      6. If the fuel tube connector and pipe are stuck, push and pull them to release them.



    A112311E02
  1. Disconnect the No. 2 fuel tank main tube.

    1. Remove the checker of the fuel tube connector from the pipe.

    2. Pinch the retainer of the fuel tube connector, and then pull out the fuel tube connector to disconnect the No. 2 fuel tank main tube from the pipe.

      NOTICE:
      1. Remove dirt or foreign objects on the fuel tube connector before this procedure.
      2. Do not allow any scratches or foreign objects on the parts when disconnecting them as the fuel tube connector has the O-rings that seal the pipe.
      3. Perform this work by hand. Do not use any tools.
      4. Do not forcibly bend, kink or twist the nylon tube.
      5. Protect the connecting part by covering it with a plastic bag after disconnecting the No. 2 fuel tank main tube.
      6. If the fuel tube connector and pipe are stuck, push and pull them to release them.



    A112312E02
  1. Disconnect the fuel tank vent hose.

    1. Pinch the retainer and pull out the fuel tank vent hose connector with the fuel tank vent hose connector pushed to the pipe side to disconnect the fuel tank vent hose from the canister filter.

      NOTICE:
      1. Remove dirt or foreign objects on the fuel tank vent hose connector before this procedure.
      2. Do not allow any scratches or foreign objects on the parts when disconnecting them as the fuel tank vent hose connector has the O-ring that seals the pipe.
      3. Perform this work by hand. Do not use any tools.
      4. Do not forcibly bend, kink or twist the nylon tube.
      5. Protect the connecting part by covering it with a plastic bag after disconnecting the fuel tank vent hose.
      6. If the fuel tank vent hose connector and pipe are stuck, push and pull them to release them.



    A112313E01
  1. Disconnect the fuel suction tube.

    1. Pinch the retainer and pull out the suction tube connector with the suction tube connector pushed to the pipe side to disconnect the fuel suction tube from the fuel tank to filler pipe.

      NOTICE:
      1. Remove dirt or foreign objects on the quick connector before this procedure.
      2. Do not allow any scratches or foreign objects on the parts when disconnecting them as the fuel suction tube connector has the O-rings that seal the pipe.
      3. Perform this work by hand. Do not use any tools.
      4. Do not forcibly bend, kink or twist the nylon tube.
      5. Protect the connecting part by covering it with a plastic bag after disconnecting the fuel suction tube.
      6. If the fuel suction tube connector and pipe are stuck, push and pull them to release them.



    A112314E01
  1. Disconnect the No. 1 canister tube.

    1. Pinch the retainer and pull out the No. 1 canister tube connector with the No. 1 canister tube connector pushed to the pipe side to disconnect the No. 1 canister tube from the fuel tank to filler pipe.

      NOTICE:
      1. Remove dirt or foreign objects on the quick connector before this procedure.
      2. Do not allow any scratches or foreign objects on the parts when disconnecting them as the No. 1 canister tube connector has the O-rings that seal the pipe.
      3. Perform this work by hand. Do not use any tools.
      4. Do not forcibly bend, kink or twist the nylon tube.
      5. Protect the connecting part by covering it with a plastic bag after disconnecting the tank to canister tube.
      6. If the No. 1 canister tube connector and pipe are stuck, push and pull them to release them.



    A087489E02
  1. Set a transmission jack to the fuel tank.

  1. Remove the fuel filler pipe clamp and fuel tube connector from the fuel tank inlet pipe.

  1. Remove the 4 bolts and No. 1 fuel tank band RH and LH.

  1. Operate the transmission jack, and then disconnect the fuel tank inlet pipe.

  1. Operate the transmission jack, and then remove the fuel tank.



8. REMOVE NO. 2 FUEL TANK MAIN TUBE SUB-ASSEMBLY


A114369
  1. Remove the 3 nuts and rear fuel tank bracket.

  1. Disconnect the wire to wire connector from the rear fuel tank bracket.



    A112315E02
  1. Disconnect the No. 2 fuel tank main tube from the clamp.

  1. Remove the checker of the main tube connector from the pipe.

  1. Pinch the retainer of the main tube connector, then pull out the fuel tube connector to disconnect the No. 2 fuel tank main tube from the pipe.

    NOTICE:
    1. Remove dirt or foreign objects on the fuel tube connector before this procedure.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting them as the fuel tube connector has the O-rings that seal the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, kink or twist the nylon tube.
    5. Protect the connecting part by covering it with a plastic bag after disconnecting the No. 2 fuel tank main tube.
    6. If the fuel tube connector and pipe are stuck, push and pull them to release them.



9. REMOVE FUEL SUCTION TUBE SUB-ASSEMBLY


    A112316E01
  1. Disconnect the fuel suction tube from the 2 No. 1 fuel tube clamps.

  1. Pinch the retainer and pull out the suction tube connector with the quick connector pushed to the pipe side to disconnect the fuel suction tube from the pipe.

    NOTICE:
    1. Remove dirt or foreign objects on the quick connector before this procedure.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting them as the suction tube connector has the O-rings that seal the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, kink or twist the nylon tube.
    5. Protect the connecting part by covering it with a plastic bag after disconnecting the fuel suction tube.
    6. If the quick connector and pipe are stuck, push and pull them to release them.



10. REMOVE FUEL TANK TO CANISTER TUBE


    A114370
  1. Disconnect the fuel tank to canister tube from the clamp.

  1. Disconnect the fuel tank to canister tube from the 2 No. 1 fuel tube clamps.

  1. Remove the fuel tank to canister tube from the fuel tank.



11. REMOVE TRAP CANISTER WITH PUMP MODULE


    A114371
  1. Disconnect the VSV connector.

  1. Remove the clamp from the fuel tank vent hose and canister hose.

  1. Remove the fuel tank vent hose from the 2 fuel tube clamps.

  1. Remove the 2 bolts and trap canister with pump module and disconnect the ground terminal of the fuel tank wire.



    A087502E01
  1. Remove the gasket from the fuel tank.



    A128672
  1. Remove the 2 clamps from the trap canister with pump module.



12. REMOVE FUEL TANK VENT HOSE


    A112317E01
  1. Pinch the retainer and pull out the fuel tank vent hose connector with the fuel tank vent hose connector pushed to the fuel tank vent hose side to disconnect the fuel tank vent hose from the trap with outlet valve canister.

    NOTICE:
    1. Remove dirt or foreign objects on the fuel tank vent hose connector before this procedure.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting them as the fuel tank vent hose connector has the O-ring that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, kink or twist the nylon tube.
    5. Protect the connecting part by covering it with a plastic bag after disconnecting the fuel tank vent hose.
    6. If the fuel tank vent hose connector and pipe are stuck, push and pull them to release them.



13. REMOVE FUEL TANK WIRE


A087496E05
  1. Remove the clamp as shown in the illustration A.

  1. Disconnect the VSV connector as shown in the illustration B.

  1. Disconnect the vapor pressure sensor connector as shown in the illustration C.

  1. Remove the 3 wire harness clamps as shown in the illustration D.



14. REMOVE CANISTER


A087497E01
  1. Disconnect the canister hose from the fuel tank retainer.

  1. Disconnect the No. 1 canister outlet hose from the fuel tank.

  1. Remove the bolt, 2 nuts and canister.



    A087498E01
  1. Remove the nut from the fuel tank.



15. REMOVE FUEL TANK PRESSURE SENSOR


    A112318E05
  1. Remove the tube joint clip, then pull out the fuel tank pressure sensor from the fuel tank retainer LH.

    NOTICE:
    1. Remove dirt or foreign objects on fuel tank pressure sensor before this procedure.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting them as the fuel tank pressure sensor has the O-ring that seals the plug.
    3. Perform this work by hand. Do not use any tools.



16. REMOVE FUEL TANK RETAINER LH


A087500E02
  1. Insert a clip remover between the fuel tank retainer and gasket, then remove the fuel tank retainer by lifting it little by little.

    NOTICE:
    1. The fuel tank retainer is made of resin and easily damaged if removed or installed forcibly. Handle the part correctly to ensure proper sealing.
    2. After removing the fuel tank retainer, check that the contact surface of the fuel tank retainer on the fuel tank is not damaged.



    A087513E01
  1. Remove the gasket from the fuel tank.



17. REMOVE NO. 1 FUEL TUBE CLAMP


A087501E01
  1. Remove the 2 clamps from the fuel tank.



18. REMOVE NO. 1 FUEL TANK CUSHION


A132605
  1. Remove the 9 cushions from the fuel tank.