Home › HYBRID SYSTEM › P112 HYBRID BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P3011    Battery Block 1 Becomes Weak

DTC    P3012    Battery Block 2 Becomes Weak

DTC    P3013    Battery Block 3 Becomes Weak

DTC    P3014    Battery Block 4 Becomes Weak

DTC    P3015    Battery Block 5 Becomes Weak

DTC    P3016    Battery Block 6 Becomes Weak

DTC    P3017    Battery Block 7 Becomes Weak

DTC    P3018    Battery Block 8 Becomes Weak

DTC    P3019    Battery Block 9 Becomes Weak

DTC    P3020    Battery Block 10 Becomes Weak

DTC    P3021    Battery Block 11 Becomes Weak

DTC    P3022    Battery Block 12 Becomes Weak

DTC    P3023    Battery Block 13 Becomes Weak

DTC    P3024    Battery Block 14 Becomes Weak

for Preparation Click here


DESCRIPTION

Refer to DTC P0A80 .

DTC No.
DTC Detection Condition
Trouble Area
P3011
P3012
P3013
P3014
P3015
P3016
P3017
P3018
P3019
P3020
P3021
P3022
P3023
P3024
Presence of a malfunctioning block is determined based on the voltages from the battery blocks (1 trip detection logic)
  1. HV battery assembly
  2. Battery ECU

MONITOR DESCRIPTION

If there is an abnormal internal resistance or electromotive voltage in the battery blocks, the battery ECU determines that a malfunction has occurred. When the malfunction detection condition is satisfied, the battery ECU illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P3011 to P3024: HV battery/Rationality
Required sensors/components
HV battery
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TOYOTA's intellectual property
Other conditions belong to TOYOTA's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


HV battery
Abnormal

COMPONENT OPERATING RANGE


HV battery
DTCs P3011 to P3024 are not detected

WIRING DIAGRAM

Refer to DTC P0AFA .

INSPECTION PROCEDURE

1.READ DTC OUTPUT (DTC P0A1F IS OUTPUT)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG) and the tester ON.

  1. Enter the following menus: Powertrain / HV Battery / DTC.

  1. Read DTCs.

    Result:
    DTC P0A1F is output



YES
REPLACE BATTERY ECU
NO


2.CHECK BATTERY BLOCK VOLTAGE
  1. Depress the brake pedal and turn the power switch ON (IG).

  1. Depress the brake pedal and accelerator pedal to charge with the HV battery.

  1. Read the battery block voltage in the DATA LIST. Enter the following menus: Powertrain / HV Battery / Data List. Read the values of "V1 Batt Block" to "V14 Batt Block".

  1. Compare the voltages as listed below.

  1. V1 Batt Block and V2 Batt Block
  2. V3 Batt Block and V4 Batt Block
  3. V5 Batt Block and V6 Batt Block
  4. V7 Batt Block and V8 Batt Block
  5. V9 Batt Block and V10 Batt Block
  6. V11 Batt Block and V12 Batt Block
  7. V13 Batt Block and V14 Batt Block

Result:
All of the battery voltage differences are 0.3 V or more.



YES
REPLACE BATTERY ECU
NO

REPLACE HV SUPPLY BATTERY ASSEMBLY