Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

ELECTRONICALLY CONTROLLED BRAKE SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK BATTERY VOLTAGE
  1. Measure the battery voltage.

    Standard voltage:
    10 to 14 V


CHECK SKID CONTROL ECU
  1. Measure the voltage and resistance between each terminal or between each terminal and the body ground.

  2. Connect Techstream to the DLC3, and check the communication condition with the skid control ECU.



  3. Using an oscilloscope, check that the pulse generates between each terminal or between each terminal and the body ground.

    NOTICE:
    1. Each inspection should be performed from the back of the connector with the connector connected to the skid control ECU.
    2. The voltage between the terminals of the brake actuator assembly may become 0 V due to the fail-safe function when the brake control warning light comes on (malfunctioning).


    C126241E02

    HINT:
    Inspect the ECU from the wire harness side while the connector is connected.


    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    R1+ (S7-2) - GND (S7-1)
    P - W
    Main relay power 1
    Push power switch ON (READY)
    9.1 to 13.6 V
    BS1 (S7-3) - GND (S7-1)
    B - W
    Battery source 1
    Push power switch ON (READY)
    Approx. 1.5 sec. after pushing power switch ON (READY)
    8.8 to 14 V
    SMC1 (S7-4) - GND (S7-1)
    Y - W
    Master cut solenoid 1 output
    Push power switch ON (READY)
    Brake pedal depressed approx. 1.5 sec. after pushing power switch ON (READY)
    Below 1.5 V
    +BCTY (S7-5) - GND (S7-1)
    V - W
    Courtesy power input
    Driver door open → close
    Approx. 5 sec. 8 to 16 V → Below 1 V
    SLAFR- (S7-6) - GND (S7-1)
    W - W
    FR solenoid (-) output
    Push power switch ON (READY)
    Approx. 1.5 sec. after pushing power switch ON (READY)
    Below 1.5 V
    SLAFR+ (S7-7) - GND (S7-1)
    R - W
    FR solenoid (+) output
    Push power switch ON (READY)
    Brake pedal depressed approx. 1.5 sec. after pushing power switch ON (READY)
    Pulse generation
    (see waveform 1)
    E (S7-8) - GND (S7-1)
    L - W
    Pressure sensor ground
    Push power switch OFF
    Below 1 Ω
    VCM1 (S7-9) - GND (S7-1)
    P - W
    Pressure sensor power
    Push power switch ON (READY)
    4.75 to 5.25 V
    MR1+ (S7-11) - GND (S7-1)
    GR - W
    Motor relay power 1
    Push power switch ON (READY)
    Approx. 1.5 sec. after pushing power switch ON (READY)
    8.8 to 14 V
    SR1 (S7-12) - GND (S7-1)
    L - W
    Main relay output 1
    Push power switch ON (READY)
    Approx. 1.5 sec. or more after pushing power switch ON (READY)
    Below 1 V
    SCSS (S7-13) - GND (S7-1)
    BR - W
    Stroke simulator cut solenoid output
    Push power switch ON (READY)
    Brake pedal depressed
    Below 1.5 V
    SLARL+ (S7-15) - GND (S7-1)
    L - W
    RL solenoid (+) output
    Push power switch ON (READY)
    Brake pedal depressed approx. 1.5 sec. after pushing power switch ON (READY)
    Pulse generation
    (see waveform 1)
    SLRRL+ (S7-16) - GND (S7-1)
    W - W
    RL solenoid (+) output
    Push power switch ON (READY)
    Brake pedal depressed approx. 1.5 sec. after pushing power switch ON (READY)
    Pulse generation
    (see waveform 1)
    SLRFR+ (S7-17) - GND (S7-1)
    Y - W
    FR solenoid (+) output
    Push power switch ON (READY)
    After approx. 1.5 sec., brake pedal depressed → released
    Pulse generation
    (see waveform 2)
    PRL (S7-18) - GND (S7-1)
    G - W
    RL pressure sensor input
    Push power switch ON (READY)
    Brake pedal released
    0.3 to 0.8 V
    SG1 (S7-20) - GND (S7-1)
    BR - W
    Pressure sensor shield ground 1
    Push power switch OFF
    Below 1 Ω
    PACC (S7-21) - GND (S7-1)
    W - W
    Accumulator pressure sensor input
    Push power switch ON (READY)
    After pump motor operates and stops by pedal operation
    3.3 to 4.7 V
    FR- (S7-22) - GND (S7-1)
    L - W
    FR sensor (-) input
    Push power switch OFF
    Below 1 Ω
    PFR (S7-23) - GND (S7-1)
    Y - W
    FR pressure sensor input
    Push power switch ON (READY)
    Brake pedal released
    0.3 to 0.8 V
    MR1 (S7-25) - GND (S7-1)
    L - W
    Motor relay output 1
    Push power switch ON (READY)
    Pump motor is operating
    Below 1.5 V
    SLRRL- (S7-26) - GND (S7-1)
    P - W
    RL solenoid (-) output
    Push power switch ON (READY)
    Approx. 1.5 sec. after pushing power switch ON (READY)
    Below 1.5 V
    SLARL- (S7-27) - GND (S7-1)
    LG - W
    RL solenoid (-) output
    Push power switch ON (READY)
    Approx. 1.5 sec. after pushing power switch ON (READY)
    Below 1.5 V
    MTT (S7-29) - GND (S7-1)
    R - W
    Motor test input
    Push power switch ON (READY)
    Pump motor is operating
    3.5 V or higher
    PMC1 (S7-30) - GND (S7-1)
    R - W
    Master pressure sensor input 1
    Push power switch ON (READY)
    Brake pedal released
    0.3 to 0.8 V
    PCK1 (S7-31) - GND (S7-1)
    B - W
    Pressure sensor check output 1
    Push power switch ON (READY)
    Approx. 1.5 sec. after pushing power switch ON (READY)
    4.75 to 5.25 V
    FR+ (S7-32) - GND (S7-1)
    P - W
    FR sensor (+) input
    Vehicle speed input
    Pulse generation
    (see waveform 3)
    SLRFR- (S7-34) - GND (S7-1)
    B - W
    FR solenoid (-) output
    Push power switch ON (READY)
    Approx. 1.5 sec. after pushing power switch ON (READY)
    Below 1.5 V
    +BI1 (S8-3) - GND (S8-1, 2)
    B - W
    Main relay power input 1
    Push power switch OFF
    10 to 14 V
    +BO1 (S8-5) - GND (S8-1, 2)
    Y - W
    Main relay power output 1
    Push power switch ON (IG)
    8.8 to 14 V
    IG1 (S8-7) - GND (S8-1, 2)
    B - W
    IG1 power
    Push power switch ON (IG)
    10 to 14 V
    RSS (S8-10) - GND (S8-1, 2)
    BR - W
    Speed sensor shield ground
    Push power switch OFF
    Below 1 Ω
    BZ (S8-12) - GND (S8-1, 2)
    BR - W
    Warning buzzer output
    Push power switch ON (READY)
    Buzzer is operating
    Below 1 V
    STP (S8-14) - GND (S8-1, 2)
    R - W
    Stop light switch signal input
    Push power switch ON (READY)
    Brake pedal depressed → released
    8 to 14 V → Below 1 V
    CAN-L (S8-18) - GND (S8-1, 2)
    W - W
    CAN communication
    (Send and receive-)
    Check DTC using Techstream
    CAN communication's DTC is not output
    CAN-H (S8-19) - GND (S8-1, 2)
    B - W
    CAN communication
    (Send and receive+)
    Check DTC using Techstream
    CAN communication's DTC is not output
    FAIL (S8-20) - GND (S8-1, 2)
    P - W
    Capacitor communication
    (Receive)
    Push power switch ON (READY)
    Approx. 1.5 sec. after pushing power switch ON (READY)
    Pulse generation
    (See waveform 5)
    SP1 (S8-22) - GND (S8-1, 2)
    V - W
    Speed meter output
    Vehicle speed input
    Pulse generation
    (See waveform 4)
    RL- (S8-27) - GND (S8-1, 2)
    B - W
    RL sensor (-) input
    Push power switch OFF
    Below 1 Ω
    D/G (S8-28) - GND (S8-1, 2)
    W - W
    Diagnosis output
    Push power switch ON (READY)
    9.1 to 13.6 V
    ENA (S8-30) - GND (S8-1, 2)
    B - W
    Capacitor communication
    (Send)
    Push power switch ON (READY)
    Approx. 1.5 sec. after pushing power switch ON (READY)
    Pulse generation
    (See waveform 6)
    TS (S8-32) - GND (S8-1, 2)
    L - W
    Sensor diagnosis check input
    Push power switch ON (READY)
    Below 1.5 V → 9.1 to 13.6 V
    VBZ (S8-33) - GND (S8-1, 2)
    B - W
    Warning buzzer power
    Push power switch ON (READY)
    9.1 to 13.6 V
    RL+ (S8-35) - GND (S8-1, 2)
    W - W
    RL sensor (+) input
    Vehicle speed input
    Pulse generation
    (See waveform 3)
    +BO2 (S9-4) - GND (S9-1, 2)
    W - W-B
    Main relay power output 2
    Push power switch ON (READY)
    8.8 to 14 V
    +BI2 (S9-5) - GND (S9-1, 2)
    R - W-B
    Main relay power input 2
    Push power switch OFF
    10 to 14 V
    VCSK (S9-6) - GND (S9-1, 2)
    B - W-B
    Stroke sensor power
    Push power switch ON (READY)
    3.75 to 4.95 V
    SSK (S9-7) - GND (S9-1, 2)
    Shielded - W-B
    Stroke sensor shield ground
    Push power switch OFF
    Below 1 Ω
    SKG (S9-8) - GND (S9-1, 2)
    W - W-B
    Stroke sensor ground
    Push power switch OFF
    Below 1 Ω
    PKB (S9-14) - GND (S9-1, 2)
    R - W-B
    Parking brake signal input
    Parking brake applied → released
    Below 1.5 V → 9.1 to 13.6 V
    SKS1 (S9-21) - GND (S9-1, 2)
    R - W-B
    Stroke sensor signal input 1
    Push power switch ON (READY)
    Brake pedal released
    0.46 to 1.35 V
    SKS2 (S9-22) - GND (S9-1, 2)
    G - W-B
    Stroke sensor signal input 2
    Push power switch ON (READY) Brake pedal released
    2.56 to 4.35 V
    RR- (S9-23) - GND (S9-1, 2)
    B - W-B
    RR sensor (-) input
    Push power switch OFF
    Below 1 Ω
    RR+ (S9-31) - GND (S9-1, 2)
    W - W-B
    RR sensor (+) input
    Vehicle speed input
    Pulse generation
    (See waveform 3)
    SLAFL+ (S10-1) - GND (S10-4)
    P - W-B
    FL solenoid (+) output
    Push power switch ON (READY)
    Brake pedal depressed approx. 1.5 sec. after pushing power switch ON (READY)
    Pulse generation
    (See waveform 1)
    SLAFL- (S10-2) - GND (S10-4)
    O - W-B
    FL solenoid (-) output
    Push power switch ON (READY)
    Approx. 1.5 sec. after pushing power switch ON (READY)
    Below 1.5 V
    SMC2 (S10-3) - GND (S10-4)
    LG - W-B
    Master cut solenoid 2 output
    Push power switch ON (READY)
    Brake pedal depressed approx. 1.5 sec. after pushing power switch ON (READY)
    Below 1.5 V
    IG2 (S10-5) - GND (S10-4)
    O - W-B
    IG2 power
    Push power switch ON (READY)
    10 to 14 V
    LBL (S10-6) - GND (S10-4)
    P - W-B
    Brake fluid level switch input
    Reservoir level switch OFF → ON
    4 to 4.65 V→ Below 1.5 V
    BS2 (S10-7) - GND (S10-4)
    P - W-B
    Battery source 2
    Push power switch ON (READY)
    Approx. 1.5 sec. after pushing power switch ON (READY)
    8.8 to 14 V
    SLRFL+ (S10-8) - GND (S10-4)
    Y - W-B
    FL solenoid (+) output
    Push power switch ON (READY)
    After approx. 1.5 sec., brake pedal depressed → released
    Pulse generation
    (See waveform 2)
    SLARR- (S10-9) - GND (S10-4)
    P - W-B
    RR solenoid (- ) output
    Push power switch ON (READY)
    Approx. 1.5 sec. after pushing power switch ON (READY)
    Below 1.5 V
    SG2 (S10-12) - GND (S10-4)
    Shielded - W-B
    Pressure sensor shield ground 2
    Push power switch OFF
    Below 1 Ω
    FSS (S10-13) - GND (S10-4)
    BR - W-B
    Speed sensor shield ground
    Push power switch OFF
    Below 1 Ω
    VCM2 (S10-14) - GND (S10-4)
    B - W-B
    Pressure sensor power 2
    Push power switch ON (READY)
    4.75 to 5.25 V
    SR2 (S10-15) - GND (S10-4)
    V - W-B
    Main relay output 2
    Push power switch ON (READY)
    Approx. 1.5 sec. after pushing power switch ON (READY)
    Below 1 V
    R2+ (S10-17) - GND (S10-4)
    Y - W-B
    Main relay power 2
    Push power switch ON (READY)
    9.1 to 13.6 V
    SLRRR- (S10-18) - GND (S10-4)
    BR - W-B
    RR solenoid (-) output
    Push power switch ON (READY)
    Approx. 1.5 sec. after pushing power switch ON (READY)
    Below 1.5 V
    SLARR+ (S10-19) - GND (S10-4)
    V - W-B
    RR solenoid (+) output
    Push power switch ON (READY)
    Brake pedal depressed approx. 1.5 sec. after pushing power switch ON (READY)
    Pulse generation
    (See waveform 1)
    SLRRR+ (S10-20) - GND (S10-4)
    R - W-B
    RR solenoid (+) output
    Push power switch ON (READY)
    Brake pedal depressed approx. 1.5 sec. after pushing power switch ON (READY)
    Pulse generation
    (See waveform 1)
    PCK2 (S10-21) - GND (S10-4)
    L - W-B
    Pressure sensor check output 2
    Push power switch ON (READY)
    4.75 to 5.25 V
    FL- (S10-22 ) - GND (S10-4)
    G - W-B
    FL sensor (-) input
    Push power switch OFF
    Below 1 Ω
    PFL (S10-23) - GND (S10-4)
    R - W-B
    FL pressure sensor input
    Push power switch ON (READY)
    Brake pedal released
    0.3 to 0.8 V
    MR2+ (S10-25) - GND (S10-4)
    R - W-B
    Motor relay power 2
    Push power switch ON (READY)
    Approx. 1.5 sec. after pushing power switch ON (READY)
    8.8 to Below 14 V
    SLRFL- (S10-26) - GND (S10-4)
    L - W-B
    FL solenoid (-) output
    Push power switch ON (READY)
    Approx. 1.5 sec. after pushing power switch ON (READY)
    Below 1.5 V
    PMC2 (S10-27) - GND (S10-4)
    W - W-B
    Master pressure sensor input 2
    Push power switch ON (READY)
    Brake pedal released
    0.3 to 0.8 V
    FL+ (S10-28) - GND (S10-4)
    R - W-B
    FL sensor (+) input
    Vehicle speed input
    Pulse generation
    (See waveform 3)
    E2 (S10-29) - GND (S10-4)
    G - W-B
    Pressure sensor ground 2
    Push power switch OFF
    Below 1 Ω
    MR2 (S10-30) - GND (S10-4)
    G - W-B
    Motor relay output 2
    Push power switch ON (READY)
    Pump motor is operating
    Below 1.5 V
    PRR (S10-31) - GND (S10-4)
    Y - W-B
    RR pressure sensor input
    Push power switch ON (READY)
    Brake pedal released
    0.3 to 0.8 V



  4. F047507E06
  5. Using an oscilloscope, check the waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Symbols (Terminal No.)
    SLAFR+ (S7-7) - GND (S7-1)
    SLARL+ (S7-15) - GND (S7-1)
    SLRRL+ (S7-16) - GND (S7-1)
    SLAFL+ (S10-1) - GND (S10-4)
    SLARR+ (S10-19) - GND (S10-4)
    SLRRR+ (S10-20) - GND (S10-4)
    Tool Setting
    5 V/DIV., 200 msec./DIV.
    Condition
    Brake pedal depressed

    NOTICE:
    Normal waveform is output only when BS 1 and 2 voltages are normal (10 to 14 V).



  6. F047507E06
  7. Using an oscilloscope, check the waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Symbols (Terminal No.)
    SLRFR+ (S7-17) - GND (S7-1)
    SLRFL+ (S10-8) - GND (S10-4)
    Tool Setting
    5 V/DIV., 200 msec./DIV.
    Condition
    Brake pedal depressed → released

    NOTICE:
    Normal waveform is output only when BS 1 and 2 voltages are normal (10 to 14 V).



  8. F047509E01
  9. Using an oscilloscope, check the waveform 3.
    Waveform 3 (Reference) 
    Item
    Content
    Symbols (Terminal No.)
    FR+ (S7-32) - GND (S7-1)
    RL+ (S8-35) - GND (S8-1, 2)
    RR+ (S9-31) - GND (S9-1, 2)
    FL+ (S10-28) - GND (S10-4)
    Tool Setting
    1 V/DIV., 200 msec./DIV.
    Condition
    While driving at approximately 18 mph (30 km/h)

    NOTICE:
    As the vehicle speed (tire rotating speed) becomes faster, the cycle becomes shorter and the output voltage becomes larger.



  10. F047510E01
  11. Using an oscilloscope, check the waveform 4.
    Waveform 4 (Reference) 
    Item
    Content
    Symbols (Terminal No.)
    SP1 (S8-22) - GND (S8-1, 2)
    Tool Setting
    5 V/DIV., 50 msec./DIV.
    Condition
    While driving at approximately 12 mph (20 km/h)

    NOTICE:
    As the vehicle speed (tire rotating speed) becomes faster, the cycle becomes shorter.



  12. F047511E01
  13. Using an oscilloscope, check the waveform 5.
    Waveform 5 (Reference) 
    Item
    Content
    Symbols (Terminal No.)
    FAIL (S8-20) - GND (S8-1, 2)
    Tool Setting
    5 V/DIV., 200 msec./DIV.
    Condition
    Power switch ON (READY)



  14. F047511E01
  15. Using an oscilloscope, check the waveform 6.
    Waveform 6 (Reference) 
    Item
    Content
    Symbols (Terminal No.)
    ENA (S8-30) - GND (S8-1, 2)
    Tool Setting
    5 V/DIV., 100 msec./DIV.
    Condition
    Power switch ON (READY)