Home › BODY ELECTRICAL › DOOR LOCK › SMART KEY SYSTEM

SMART KEY SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK CERTIFICATION ECU

B119823E01

  1. Disconnect the S11 ECU connector.

  2. Measure the resistance and voltage of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    +B1 (S11-1) - Body ground
    R - Body ground
    +B power supply
    Always
    10 to 14 V
    IG (S11-18) - Body ground
    B - Body ground
    Ignition power supply
    Power switch OFF
    Below 1 V
    IG (S11-18) - Body ground
    B - Body ground
    Ignition power supply
    Power switch ON (IG)
    10 to 14 V
    E (S11-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    TSW1 (S11-5) - Body ground
    B - Body ground
    Outside door handle LH lock switch signal
    Lock switch OFF
    10 kΩ or higher
    TSW1 (S11-5) - Body ground
    B - Body ground
    Outside door handle LH lock switch signal
    Lock switch ON
    Below 1 Ω
    TSW2 (S11-6) - Body ground
    R - Body ground
    Outside door handle RH lock switch signal
    Lock switch OFF
    10 kΩ or higher
    TSW2 (S11-6) - Body ground
    R - Body ground
    Outside door handle RH lock switch signal
    Lock switch ON
    Below 1 Ω
    TSW6 (S11-8) - Body ground
    B - Body ground
    Back door lock switch signal
    Back door lock switch OFF
    10 kΩ or higher
    TSW6 (S11-8) - Body ground
    B - Body ground
    Back door lock switch signal
    Back door lock switch ON
    Below 1 Ω
    CNSL (S11-25) - Body ground
    W-B - Body ground
    Key cancel switch signal
    Key cancel switch OFF
    10 kΩ or higher
    CNSL (S11-25) - Body ground
    W-B - Body ground
    Key cancel switch signal
    Key cancel switch ON
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the S11 ECU connector.

  4. Measure the voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    CLG1 (S11-13) - E (S11-17)
    P - W-B
    Driver door electrical key oscillator sensor signal
    All doors closed, all doors locked and power switch OFF
    Alternating between 5 V and below 1 V
    CLG1 (S11-13) - E (S11-17)
    P - W-B
    Driver door electrical key oscillator sensor signal
    Door unlocked or door open
    Below 1 V
    CLG2 (S11-14) - E (S11-17)
    R - W-B
    Front passenger door electrical key oscillator sensor signal
    All doors closed, all doors locked and power switch OFF
    Alternating between 5 V and below 1 V
    CLG2 (S11-14) - E (S11-17)
    R - W-B
    Front passenger door electrical key oscillator sensor signal
    Door unlocked or door open
    Below 1 V
    CLG5 (S11-36) - E (S11-17)
    G - W-B
    Indoor electrical key oscillator sensor signal
    30 seconds after driver side door opened and closed, power switch OFF
    Alternating between 5 V and below 1 V
    CLG5 (S11-36) - E (S11-17)
    G - W-B
    Indoor electrical key oscillator sensor signal
    Within 30 seconds after driver side door opened and closed, power switch ON (IG)
    Below 1 V
    CLG7 (S11-38) - E (S11-17)
    BR - W-B
    Luggage electrical key oscillator inner sensor signal
    Back door opener switch OFF
    Alternating between 5 V and below 1 V
    CLG7 (S11-38) - E (S11-17)
    BR - W-B
    Luggage electrical key oscillator inner sensor signal
    Back door opener switch ON
    Below 1 V
    CLG8 (S11-39) - E (S11-17)
    O - W-B
    Luggage electrical key oscillator outer sensor signal
    Back door opener switch OFF
    Alternating between 5 V and below 1 V
    CLG8 (S11-39) - E (S11-17)
    O - W-B
    Luggage electrical key oscillator outer sensor signal
    Back door opener switch ON
    Below 1 V
    SEL1 (S11-23) - E (S11-17)
    Y - W-B
    Touch sensor activation control signal
    Key at least 3 m (9.8 ft.) away from closed and locked door
    10 to 14 V
    SEL1 (S11-23) - E (S11-17)
    Y - W-B
    Touch sensor activation control signal
    Key is near closed and locked door
    Below 1 V
    SEL2 (S11-24) - E (S11-17)
    B - W-B
    Touch sensor activation control signal
    Key at least 3 m (9.8 ft.) away from closed and locked door
    10 to 14 V
    SEL2 (S11-24) - E (S11-17)
    B - W-B
    Touch sensor activation control signal
    Key is near closed and locked door
    Below 1 V
    SEN1 (S11-21) - E (S11-17)
    R - W-B
    Touch sensor detection signal
    Outside door handle LH touched
    10 to 14 V
    SEN1 (S11-21) - E (S11-17)
    R - W-B
    Touch sensor detection signal
    Outside door handle LH not touched
    Below 1 V
    SEN2 (S11-22) - E (S11-17)
    W - W-B
    Touch sensor detection signal
    Outside door handle RH touched
    10 to 14 V
    SEN2 (S11-22) - E (S11-17)
    W - W-B
    Touch sensor detection signal
    Outside door handle RH not touched
    Below 1 V
    RDA3 (S11-29) - E (S11-17)
    L - W-B
    Door control receiver input signal
    With power switch OFF, no key and all doors closed
    Below 1 V
    RDA3 (S11-29) - E (S11-17)
    L - W-B
    Door control receiver input signal
    With power switch OFF, all doors closed and key is moved (outside of vehicle exterior detection area → inside of detection area)
    Approx. 6 to 7 V
    PRG (S11-28) - E (S11-17)
    B - W-B
    Door control receiver output signal
    With power switch OFF, no key and all doors closed
    Below 1 V
    PRG (S11-28) - E (S11-17)
    B - W-B
    Door control receiver output signal
    With power switch OFF, all doors closed and key is moved (outside of vehicle exterior detection area → inside of detection area)
    Approx. 6 to 7 V
    RCO (S11-12) - E (S11-17)
    L - W-B
    Power source
    With power switch OFF, no key and doors closed
    0 to 5 V
    RCO (S11-12) - E (S11-17)
    L - W-B
    Power source
    With power switch OFF, all doors closed and key is moved (outside of vehicle exterior detection area → inside of detection area)
    5 V
    RSSI (S11-11) - E (S11-17)
    V - W-B
    Door control receiver output signal
    With power switch OFF, no key and all doors closed
    0 to 5 V
    RSSI (S11-11) - E (S11-17)
    V - W-B
    Door control receiver output signal
    With power switch OFF, all doors closed and key is moved (outside of vehicle exterior detection area → inside of detection area)
    Below 1 V
    RDA (S11-10) - E (S11-17)
    GR - W-B
    Door control receiver input signal
    With power switch OFF, no key and all doors closed
    Below 1 V
    RDA (S11-10) - E (S11-17)
    GR - W-B
    Door control receiver input signal
    With power switch OFF, all doors closed and key is moved (outside of vehicle exterior detection area → inside of detection area)
    Approx. 6 to 7 V
    KSW (S11-4) - E (S11-17)
    Y - W-B
    Halfway switch input signal
    No key in key slot
    10 to 14 V
    KSW (S11-4) - E (S11-17)
    Y - W-B
    Halfway switch input signal
    Key inserted
    Below 1 V

  1. If the result is not as specified, the ECU may have a malfunction.

CHECK DRIVER SIDE JUNCTION BLOCK (MAIN BODY ECU)

B119824E02

  1. Disconnect the 1A, 1B and 1E junction block connectors.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    ECUB (1A-30) - Body ground
    R - Body ground
    +B (ECUB) power supply
    Always
    10 to 14 V
    ALTB (1B-1) - Body ground
    W - Body ground
    +B (power system, generator system) power supply
    Always
    10 to 14 V
    GND (1E-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the 1A, 1B and 1E junction block connectors.

  4. Measure the voltage of the connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    PRG (B7-24) - GND (1E-17)
    B - W-B
    Door control receiver output signal
    With power switch OFF, no key and all doors closed
    0 to 5 V
    PRG (B7-24) - GND (1E-17)
    B - W-B
    Door control receiver output signal
    With power switch OFF, all doors closed and key is moved (outside of vehicle exterior detection area → inside of detection area)
    Below 1 V
    RDA (B7-23) - GND (1E-17)
    L - W-B
    Door control receiver input signal
    With power switch OFF, no key and all doors closed
    Below 1 V
    RDA (B7-23) - GND (1E-17)
    L - W-B
    Door control receiver input signal
    With power switch OFF, all doors closed and key is moved (outside of vehicle exterior detection area → inside of detection area)
    Approx. 6 to 7 V

    1. If the result is not as specified, the body ECU may have a malfunction.


CHECK TRANSPONDER KEY ECU

B126056E01

  1. Disconnect the T5 ECU connector.

  2. Measure the resistance and voltage of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    CPUB (T5-3) - GND (T5-22)
    L - W-B
    Battery
    Always
    10 to 14 V
    IG (T5-4) - GND (T5-22)
    O - W-B
    Power switch (IG)
    Power switch OFF
    Below 1 V
    IG (T5-4) - GND (T5-22)
    O - W-B
    Power switch (IG)
    Power switch ON (IG)
    10 to 14 V
    CUWS (T5-5) - GND (T5-22)
    B - W-B
    Halfway switch
    No key in key slot
    10 kΩ or higher
    CUWS (T5-5) - GND (T5-22)
    B - W-B
    Halfway switch
    Key inserted
    Below 1 Ω
    AGND (T5-7) - GND (T5-22)
    P - W-B
    Ground
    Always
    Below 1 Ω
    GND (T5-22) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the T5 ECU connector.

  4. Measure the voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    CUWS (T5-5) -GND (T5-22)
    B - W-B
    Halfway switch
    No key in key slot
    10 to 14 V
    CUWS (T5-5) -GND (T5-22)
    B - W-B
    Halfway switch
    Key inserted
    Below 1 V
    VC5 (T5-20) - GND (T5-22)
    Y - W-B
    Power source
    No key in key slot
    Below 1 V
    VC5 (T5-20) - GND (T5-22)
    Y - W-B
    Power source
    Key inserted
    4.6 to 5.4 V
    CODE (T5-21) - AGND (T5-7)
    L - P
    Transponder key amplifier communication signal
    No key in key slot → Key inserted
    Pulse generation (see waveform 1)
    TXCT (T5-6) - AGND (T5-7)
    LG - P
    Transponder key amplifier communication signal
    No key in key slot → Key inserted
    Pulse generation (see waveform 2)
    HEV0 (T5-19) - GND (T5-22)
    W - W-B
    Hybrid vehicle control ECU output signal
    No key in key slot → Key inserted
    Pulse generation (see waveform 3)
    HEV1 (T5-18) - GND (T5-22)
    R - W-B
    Hybrid vehicle control ECU input signal
    Always
    Pulse generation (see waveform 4)

    1. If the result is not as specified, the ECU may have a malfunction.



  5. B051052E05
  6. Inspect using an oscilloscope.
    Waveform 1 (Reference) 
    Item
    Content
    Symbols (Terminal No.)
    TXCT (T5-6) - GND (T5-22)
    Tool Setting
    2.0 V/DIV., 10 msec./DIV.
    Condition
    Key inserted



  7. B051053E06
  8. Inspect using an oscilloscope.
    Waveform 2 (Reference) 
    Item
    Content
    Symbols (Terminal No.)
    CODE (T5-21) - GND (T5-22)
    Tool Setting
    2.0 V/DIV., 10 msec./DIV.
    Condition
    Key inserted



  9. B051050E04
  10. Inspect using an oscilloscope.
    Waveform 3 (Reference) 
    Item
    Content
    Symbols (Terminal No.)
    HEV0 (T5-19) - GND (T5-22)
    Tool Setting
    10 V/DIV., 100 msec./DIV.
    Condition
    Power switch ON (IG)



  11. B051051E05
  12. Inspect using an oscilloscope.
    Waveform 4 (Reference) 
    Item
    Content
    Symbols (Terminal No.)
    HEV1 (T5-18) - GND (T5-22)
    Tool Setting
    10 V/DIV., 100 msec./DIV.
    Condition
    Always