Home › STEERING › POWER STEERING › ELECTRONIC POWER STEERING SYSTEM

ELECTRONIC POWER STEERING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the Techstream (with CAN VIM) to the DLC3.

  2. Turn the power switch ON (IG).

  3. Turn the Techstream on.

  4. Read the Data List. Enter the following menus: Chassis / EMPS / Data List.

  5. According to the display on the Techstream, read the Data List.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Torque Sensor 1 Output
    Torque sensor 1 output value / min.: 0 V, max.: 5 V
    2.3 to 2.7 V
    Steering wheel is not turned (without load)
    2.5 to 4.7 V
    Turning steering wheel to right with vehicle stopped
    0.3 to 2.5 V
    Turning steering wheel to left with vehicle stopped
    Torque Sensor 2 Output
    Torque sensor 2 output value / min.: 0 V, max.: 5 V
    2.3 to 2.7 V
    Steering wheel is not turned (without load)
    2.5 to 4.7 V
    Turning steering wheel to right with vehicle stopped
    0.3 to 2.5 V
    Turning steering wheel to left with vehicle stopped
    Torque Sensor 3 Output
    Torque value for assist control / min.: 0 V, max.: 5 V
    2.3 to 2.7 V
    Steering wheel is not turned (without load)
    2.5 to 4.7 V
    Turning steering wheel to right with vehicle stopped
    0.3 to 2.5 V
    Turning steering wheel to left with vehicle stopped
    Meter Vehicle Velocity
    Vehicle speed from meter / min.: 0 km/h, max.: 255 km/h
    0 km/h
    Vehicle is stopped
    No significant fluctuation
    Vehicle is driven at a constant speed
    Motor Actual Current
    Amount of current to motor / min.: -128 A, max.: 127 A
    -
    -
    Command Value Current
    Demanded amount of current to motor / min.: -128 A, max.: 127 A
    -
    -
    Thermistor Temperature
    ECU substrate temperature / min.: -50°C, max.: 205°C
    -
    Power switch is ON (IG)
    PIG Power Supply
    Power source voltage to activate motor / min.: 0 V, max.: 25.5 V
    10 to 16 V
    Power steering is in operation
    IG Power Supply
    ECU power source voltage / min.: 0 V, max.: 25.5 V
    10 to 16 V
    -
    TRQ1 Zero Point Value
    Zero point value of torque sensor 1 / min.: 0 V, max.: 5 V
    2.3 to 2.7 V
    Steering wheel is not turned (without load)
    TRQ2 Zero Point Value
    Zero point value of torque sensor 2 / min.: 0 V, max.: 5 V
    2.3 to 2.7 V
    Steering wheel is not turned (without load)
    TRQ3 Zero Point Value
    Zero point value of torque sensor for assist control / min.: 0 V, max.: 5 V
    2.3 to 2.7 V
    Steering wheel is not turned (without load)
    Motor Terminal Volt (+)
    Motor terminal M1 voltage / min.: 0 V, max.: 22.5 V
    10 to 16 V
    Turning steering wheel to right
    Below 1 V
    Turning steering wheel to left
    Motor Terminal Volt (-)
    Motor terminal M2 voltage / min.: 0 V, max.: 22.5 V
    Below 1 V
    Turning steering wheel to right
    10 to 16 V
    Turning steering wheel to left
    Motor Overheat Record
    Continuous overheat prevention control record / Rec or Unrec
    -
    -
    Motor Lo Power Record
    PIG power source voltage drop record / Rec or Unrec
    -
    -
    Control Mode
    Codes indicating DTC detection timing during ECU control are displayed in hexadecimal / min.: 0, max.: 255
    -
    -
    IG ON/OFF Times
    Number of times power switch is turned on (IG) after DTC detection / min.: 0 times, max.: 255 times
    -
    -
    The Number of DTCs
    Number of detected DTCs when freeze frame data is stored / min.: 0, max.: 255
    -
    -
    ECU Identification
    ECU identification information
    -
    -
    Test Mode Status
    Selected mode / Normal or Test
    -
    -
    Ready Status
    HV system / Ready or OFF
    ON
    HV system "READY"
    OFF
    HV system not "READY"