ELECTRONIC POWER STEERING SYSTEM > FREEZE FRAME DATA |
| FREEZE FRAME DATA |
Connect the Techstream (with CAN VIM) to the DLC3.
Turn the power switch ON (IG).
Turn the Techstream on.
Check the freeze frame data. Enter the following menus: Chassis / EMPS / Utility / Freeze Frame Data.
| Tester Display | Item Description/Range | Inspection Condition | Reference Value |
| Torque Sensor 1 Output | Torque sensor 1 output value / min.: 0 V, max.: 5 V | Steering wheel is not turned (without load) | 2.3 to 2.7 V |
| Turning steering wheel to right with vehicle stopped | 2.5 to 4.7 V | ||
| Turning steering wheel to left with vehicle stopped | 0.3 to 2.5 V | ||
| Torque Sensor 2 Output | Torque sensor 2 output value / min.: 0 V, max.: 5 V | Steering wheel is not turned (without load) | 2.3 to 2.7 V |
| Turning steering wheel to right with vehicle stopped | 2.5 to 4.7 V | ||
| Turning steering wheel to left with vehicle stopped | 0.3 to 2.5 V | ||
| Torque Sensor 3 Output | Torque value for assist control / min.: 0 V, max.: 5 V | Steering wheel is not turned (without load) | 2.3 to 2.7 V |
| Turning steering wheel to right with vehicle stopped | 2.5 to 4.7 V | ||
| Turning steering wheel to left with vehicle stopped | 0.3 to 2.5 V | ||
| Meter Vehicle Velocity | Vehicle speed from meter / min.: 0 km/h, max.: 255 km/h | Vehicle is stopped | 0 km/h |
| Vehicle is driven at a constant speed | No significant fluctuation | ||
| Motor Actual Current | Amount of current to motor / min.: -128 A, max.: 127 A | - | - |
| Command Value Current | Demanded amount of current to motor / min.: -128 A, max.: 127 A | - | - |
| Thermistor Temperature | ECU substrate temperature / min.: -50°C, max.: 205°C | Power switch is ON (IG) | - |
| PIG Power Supply | Power source voltage to activate motor / min.: 0 V, max.: 25.5 V | Power steering is in operation | 10 to 16 V |
| IG Power Supply | ECU power source voltage / min.: 0 V, max.: 25.5 V | - | 10 to 16 V |
| TRQ1 Zero Point Value | Zero point value of torque sensor 1 / min.: 0 V, max.: 5 V | Steering wheel is not turned (without load) | 2.3 to 2.7 V |
| TRQ2 Zero Point Value | Zero point value of torque sensor 2 / min.: 0 V, max.: 5 V | Steering wheel is not turned (without load) | 2.3 to 2.7 V |
| TRQ3 Zero Point Value | Zero point value of torque sensor for assist control / min.: 0 V, max.: 5 V | Steering wheel is not turned (without load) | 2.3 to 2.7 V |
| Motor Terminal Volt (+) | Motor terminal M1 voltage / min.: 0 V, max.: 22.5 V | Turning steering wheel to right | 10 to 16 V |
| Turning steering wheel to left | Below 1 V | ||
| Motor Terminal Volt (-) | Motor terminal M2 voltage / min.: 0 V, max.: 22.5 V | Turning steering wheel to right | Below 1 V |
| Turning steering wheel to left | 10 to 16 V | ||
| Ready Status | HV system / Ready or OFF | HV system "READY" | Ready |
| HV system not "READY" | OFF |