Home › ENGINE › 1NZ-FXE STARTING › SMART KEY SYSTEM

SMART KEY SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using Techstream's DATA LIST allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the DATA LIST early in troubleshooting is one way to save time.

  1. Connect Techstream to the DLC3.

  2. Turn the power switch ON (IG).

  3. Read the DATA LIST according to the display on the tester.

    Power source control ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Steering Unlock Switch
    Steering unlock switch /
    ON or OFF
    ON: Key is in key slot
    OFF: No key is in key slot
    -
    Ready Signal
    Ready signal /
    ON or OFF
    ON: Power switch ON (READY)
    OFF: Power switch OFF or ON (IG) or ON (ACC)
    -
    Vehicle Speed Signal
    Vehicle speed signal /
    ON or OFF
    Stop: Vehicle is stopped
    Run: Vehicle is running
    -
    Shift P Signal
    Shift P signal /
    ON or OFF
    ON: Shift P signal ON (shift position is P)
    OFF: Shift P signal OFF (shift position is not P)
    -
    Shift P Signal
    Shift P signal pulse /
    Unknown, Error2, Normal2, Error1, Normal3, Error3 or Normal1
    Unknown: Other
    Error2: Signal is abnormal and shift position is P
    Normal2: Signal is normal and shift position is P
    Error1: Signal is abnormal and shift position cannot be determined
    Normal3: Signal is normal and shift position in not P
    Error3: Signal is abnormal and shift position in not P
    Normal1: Signal is normal and shift position cannot be determined
    -
    Card Halfway Switch
    Halfway switch /
    ON or OFF
    ON: Key is half-inserted
    OFF: Key is not half-inserted
    -
    Card Full Switch
    Full switch /
    ON or OFF
    ON: Key is fully inserted
    OFF: Key is not fully inserted
    -
    Stop Light Switch1
    Stop light switch 1 /
    ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Stop Light Switch2
    Stop light switch 2 /
    ON or OFF
    ON: Brake pedal released
    OFF: Brake pedal depressed
    -
    Start Switch1
    Start switch 1 /
    ON or OFF
    ON: Power switch ON (IG)
    OFF: Power switch OFF
    -
    Start Switch2
    Start switch 2 /
    ON or OFF
    ON: Power switch ON (IG)
    OFF: Power switch OFF
    -
    Latch Circuit
    Ratch circuit /
    ON or OFF
    ON: Power switch ON (IG)
    OFF: Power switch OFF or ON (ACC) or ON (READY)
    -
    IG1 Relay Monitor (Outside)
    IG1 outer relay monitor /
    ON or OFF
    ON: Power switch ON (IG)
    OFF: Power switch OFF
    -
    IG1 Relay Monitor (Inside)
    IG1 inner relay monitor /
    ON or OFF
    ON: Power switch ON (IG)
    OFF: Power switch OFF
    -
    IG2 Relay Monitor (Outside)
    States of the IG2 outer relay monitor /
    ON or OFF
    ON: Power switch ON (IG)
    OFF: Power switch OFF
    -
    IG2 Relay Monitor (Inside)
    IG2 Inner relay monitor /
    ON or OFF
    ON: Power switch ON (IG)
    OFF: Power switch OFF
    -
    ACC Relay Monitor
    ACC relay monitor /
    ON or OFF
    ON: Power switch ON (ACC)
    OFF: Power switch OFF
    -
    Power Supply Condition
    Power supply condition /
    IG2 ON, ST ON, All OFF, IG1 ON or ACC ON
    IG2 ON: IG2 relay ON
    ST ON: ST relay ON
    All OFF: All relay OFF
    IG1 ON: IG1 relay ON
    ACC ON: ACC relay ON
    -


PERFORM ACTIVE TEST

HINT:
Performing Techstream's ACTIVE TEST allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time. The DATA LIST can be displayed during the ACTIVE TEST.

  1. Connect Techstream to the DLC3.

  2. Turn the power switch ON (IG).

  3. Perform the ACTIVE TEST according to the display on the tester.

    Power source control ECU 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    KEY Lock
    Key lock (turn power switch OFF during test; turn power switch ON (IG)) ON / OFF
    ON / OFF
    -
    Indicator for lighting
    Indicator for lighting ON / OFF
    ON / OFF
    -
    Indicator Condition
    Indicator Green / Red / No Sig
    Red / No Sig
    -