Home › ENGINE › 1NZ-FXE STARTING › SMART KEY SYSTEM

SMART KEY SYSTEM > Power Source Mode does not Change to ON (IG)

for Preparation Click here


DESCRIPTION

When the key is inserted into the key slot and the power switch is pressed, signals are input to the power source control ECU. Selection of the power mode, which cycles between OFF, ON (ACC) and ON (IG), is performed by pressing and releasing the power switch until the desired power mode is selected (the power modes cycle in the order shown above).

WIRING DIAGRAM


B135509E01


INSPECTION PROCEDURE

1.INSPECT FUSE (AM1, AM2)
  1. Remove the AM1 fuse from the driver side junction block.

  1. Remove the AM2 fuse from the engine room junction block.

  1. Measure the resistance of the fuses.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2.CHECK WIRE HARNESS (POWER SOURCE CONTROL ECU - BATTERY AND BODY GROUND)


    B079748E04
  1. Disconnect the P6 ECU connector.

  1. Measure the resistance and voltage of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    P6-6 (GND2) - Body ground
    Below 1 Ω
    Standard voltage:
    Tester Connection
    Specified Condition
    P6-33 (AM1) - Body ground
    10 to 14 V
    P6-12 (AM2) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3.CHECK FOR DTC
  1. Check for DTCs of the power source control ECU.

    OK:
    DTCs of the power source control ECU are not output.



NG
GO TO DTC CHART
OK


4.INSPECT IG1 RELAY


    B112776E02
  1. Remove the IG1 relay from the driver side junction block.

  1. Measure the resistance of the relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage is applied to terminals 1 and 2)



NG
REPLACE IG1 RELAY
OK


5.CHECK WIRE HARNESS (DRIVER SIDE JUNCTION BLOCK - ECU AND BODY GROUND)


    B128121E01
  1. Disconnect the 1J and 1E junction block connectors.

  1. Disconnect the P6 ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    1J-3 - P6-34 (IG1D)
    Below 1 Ω
    1E-17 - Body ground
    Below 1 Ω
    1J-3 or P6-34 (IG1D) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.INSPECT DRIVER SIDE JUNCTION BLOCK


    B135432E01
  1. Disconnect the 1J and 1E junction block connectors.

  1. Remove the IG1 relay from the driver side junction block.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    1J-3 - Driver side junction block IG1 relay terminal 2
    Below 1 Ω
    1E-17 - Driver side junction block IG1 relay terminal 1
    Below 1 Ω



NG
REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY
OK


7.CHECK WIRE HARNESS (ENGINE ROOM JUNCTION BLOCK - ECU AND BODY GROUND)


    B080046E01
  1. Disconnect the 3I junction block connector.

  1. Disconnect the P6 ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    3I-2 - P6-35 (IG2D)
    Below 1 Ω
    3I-3 - Body ground
    Below 1 Ω
    3I-2 or P6-35 (IG2D) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


8.CHECK POWER SOURCE CONTROL ECU (IG1D, IG2D VOLTAGE)


    B135413E01
  1. Measure the voltage of the connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    P6-34 (IG1D) - Body ground
    Power switch ON (ACC)
    Below 1 V
    P6-35 (IG2D) - Body ground
    Power switch ON (ACC)
    Below 1 V
    P6-34 (IG1D) - Body ground
    Power switch ON (IG)
    10 to 14 V
    P6-35 (IG2D) - Body ground
    Power switch ON (IG)
    10 to 14 V



NG
REPLACE POWER SOURCE CONTROL ECU
OK


9.CHECK ENGINE ROOM RELAY BLOCK


    B135414E01
  1. Measure the voltage of the connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    3I-4 - Body ground
    Power switch ON (IG)
    10 to 14 V



NG
REPLACE ENGINE ROOM RELAY BLOCK
OK


10.CHECK OPERATION OF POWER SOURCE CONTROL ECU
  1. After replacing the power source control ECU with a normally functioning ECU, check that the power switch can be set to ON (IG).

    Result 
    Result
    Proceed to
    Power switch can be set to ON (IG)
    A
    Power switch cannot be set to ON (IG) (w/ smart key system (for door lock))
    B
    Power switch cannot be set to ON (IG) (w/o smart key system (for door lock))
    C



B
GO TO ENGINE IMMOBILISER SYSTEM (w/ SMART KEY SYSTEM)

C
GO TO ENGINE IMMOBILISER SYSTEM (w/o SMART KEY SYSTEM)
A

NORMAL (POWER SOURCE CONTROL ECU DEFECTIVE)