Home › HYBRID SYSTEM › HYBRID TRANSMISSION / TRANSAXLE › ELECTRONIC SHIFT LEVER SYSTEM

ELECTRONIC SHIFT LEVER SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the Techstream's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch ON (IG) and press the Techstream main switch on.

  3. Read the Data List by following the directions on the tester screen.

    Transmission control ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Shift Pos Display (P)
    Shift position display (P) / ON or OFF
    ON: Parking lock is in P position
    OFF: Parking lock is in non-P position
    -
    Shift Pos Display (Not P)
    Shift position display (not P) / ON or OFF
    ON: Parking lock is in non-P position
    OFF: Parking lock is in P position
    -
    Master Caution Display
    Master caution display / DISP or NONDISP
    DISP: Malfunction occurs in this system
    NONDISP: Malfunction does not occur in this system
    -
    PSW Indicator Mode
    PSW indicator mode / OFF, ON, FAST, or SLOW
    OFF: Parking lock is in non-P position
    ON: Parking lock is in P position
    FAST: Actuator takes long time to switch between the P position and non-P position
    SLOW: Malfunction occurs in this system
    -
    U Phase Voltage Value
    U phase voltage value / min: 0 V, max: 20 V
    Actual U phase voltage 9 to 14 V
    -
    V Phase Voltage Value
    V phase voltage value / min: 0 V, max: 20 V
    Actual V phase voltage 9 to 14 V
    -
    W Phase Voltage Value
    W phase voltage value / min: 0 V, max: 20 V
    Actual W phase voltage 9 to 14 V
    -
    Battery Voltage Value
    BATT voltage value / min: 0 V, max: 20 V
    Actual power supply voltage 9 to 14 V
    -
    IG(+B) Voltage Value
    IG (+B) voltage value / min: 0 V, max: 20 V
    Actual power supply voltage 9 to 14 V
    -
    P Sply OFF Prepare Rqst Sig
    Power supply off preparation request signal / ON or OFF
    ON: Power is turned off by power source control ECU after receiving power switch OFF signal
    OFF: Any other condition
    -
    Cmplte of Learn Lck Pos
    Completion of learning lock position / OK or NG
    OK: Lock position learning is complete
    NG: Lock position learning is not complete
    -
    Cmplte of Learn Unlck Pos
    Completion of learning unlock position / OK or NG
    OK: Unlock position learning is complete
    NG: Unlock position learning is not complete
    -
    # of Trip Cuntr after Learn
    Number of trip counter after learning / min: 0, max: 65535
    Actual number of trip counter
    Reset the trip counter after 1,000 times
    Main Relay for Motor Drive
    Main relay for motor drive / ON or OFF
    ON: Motor drive main relay on
    OFF: Motor drive main relay off
    -
    Sig of Electric Key Cond
    Signal of electrical key condition / ON or OFF
    ON: Electrical key is recognized
    OFF: Electrical key is not recognized
    -
    Number of Diagnosis Code
    Number of diagnosis code / min: 0, max: 255
    Actual number of diagnosis code
    -
    U Phase Crnt-Carry Status
    U phase current-carrying status / ON or OFF
    ON: U phase current flows
    OFF: U phase current does not flow
    -
    V Phase Crnt-Carry Status
    V phase current-carrying status / ON or OFF
    ON: V phase current flows
    OFF: V phase current does not flow
    -
    W Phase Crnt-Carry Status
    W phase current-carrying status / ON or OFF
    ON: W phase current flows
    OFF: W phase current does not flow
    -
    U Phase Voltage Status
    U phase voltage status / ON or OFF
    ON: U phase voltage is 6 V or more
    OFF: U phase voltage is less than 6 V
    -
    V Phase Voltage Status
    V phase voltage status / ON or OFF
    ON: V phase voltage is 6 V or more
    OFF: V phase voltage is less than 6 V
    -
    W Phase Voltage Status
    W phase voltage status / ON or OFF
    ON: W phase voltage is 6 V or more
    OFF: W phase voltage is less than 6 V
    -
    Battery Voltage Status
    BATT voltage status / ON or OFF
    ON: BATT voltage is more than 10 V
    OFF: BATT voltage is 10 V or less
    -
    IG (+B) Phase Voltage Status
    IG (+B) phase voltage status / ON or OFF
    ON: +B voltage is more than 10 V
    OFF: +B voltage is 10 V or less
    -
    ACC Condition Signal
    ACC condition signal / ON or OFF
    ON: ACC condition signal is normal
    OFF: ACC condition signal is interrupted
    -
    Init Drv Cntrl Completed
    Initial drive control completed / OK or NG
    OK: Initial drive control is complete
    NG: Initial drive control is not complete
    -
    Cmplte of Detect Lck Pos
    Completion of detecting lock position / OK or NG
    OK: Detection of lock position is complete
    NG: Detection of lock position is not complete
    -
    Cmplte of Detect Unlck Pos
    Completion of detecting unlock position / OK or NG
    OK: Detection of unlock position is complete
    NG: Detection of unlock position is not complete
    -
    P/Not P Move Shft Range
    P/Not P movable shift range / SET or UNSET
    SET: P/Not P movable shift range is set
    UNSET: P/Not P movable shift range is unset
    -
    Main Relay
    Main relay / NORMAL or ABNOML
    NORMAL: Main relay is normal
    ABNOML: Main relay is fault
    -
    Vehicle Condition
    Vehicle condition / STOP or MOVE
    STOP: Vehicle is stopped
    MOVE: Vehicle is running
    -
    Type of ECU
    Type of ECU / min: 0, max: 65535
    Actual type of ECU
    -