Home › HYBRID SYSTEM › HYBRID TRANSMISSION / TRANSAXLE › ELECTRONIC SHIFT LEVER SYSTEM

DTC    C2304    Open or Short Circuit in "U" Phase

DTC    C2305    Open or Short Circuit in "V" Phase

DTC    C2306    Open or Short Circuit in "W" Phase

for Preparation Click here


DESCRIPTION

The shift control actuator consists of the parking lock motor and the rotation angle sensor. The transmission control ECU receives a P position switch signal from the hybrid vehicle control ECU and activates the parking lock motor by controlling current, causing the parking lock mechanism to switch. The transmission control ECU outputs this DTC when it detects a malfunction in the parking lock motor system.

DTC No.
DTC Detection Condition
Trouble Area
C2304
When both conditions below are met:
  1. Power switch ON (IG) (battery voltage is 8 V or more).
  2. Voltage of transmission control ECU terminal MUA is 6 V or less for 1 second or more.
  1. Shift control actuator
  2. Transmission control ECU
  3. Transaxle parking lock control relay (P CON Relay)
  4. Wire harness or connector
C2305
When both conditions below are met:
  1. Power switch ON (IG) (battery voltage is 8 V or more).
  2. Voltage of transmission control ECU terminal MVA is 6 V or less for 1 second or more.
  1. Shift control actuator
  2. Transmission control ECU
  3. Transaxle parking lock control relay (P CON Relay)
  4. Wire harness or connector
C2306
When both conditions below are met:
  1. Power switch ON (IG) (battery voltage is 8 V or more).
  2. Voltage of transmission control ECU terminal MWA is 6 V or less for 1 second or more.
  1. Shift control actuator
  2. Transmission control ECU
  3. Transaxle parking lock control relay (P CON Relay)
  4. Wire harness or connector

WIRING DIAGRAM


C126769E03


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Turn the Techstream on.

  1. Read the DTCs.

    Result 
    Display (DTC output)
    Proceed to
    C2304, C2305 and C2306 are detected simultaneously
    A
    C2304, C2305 and C2306 are not detected simultaneously
    B

    HINT:
    1. When DTCs C2304, C2305 and C2306 are detected simultaneously, there may be an open or short circuit between the shift control actuator and the battery.
    2. When DTCs C2304, C2305 and C2306 are not detected simultaneously, there may be an open or short circuit in the shift control actuator or between the actuator and the ECU.



B
Go to step 6
A


2.CHECK WIRE HARNESS (SHIFT CONTROL ACTUATOR - BATTERY)


    C126783E01
  1. Disconnect the S1 actuator connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S1-2 (MGNA) - Body ground
    Power switch ON (IG)
    9 to 14 V



OK
Go to step 6
NG


3.INSPECT FUSE (P CON MTR FUSE)
  1. Remove the P CON MTR H-fuse from the engine room relay block.

  1. Measure the resistance of the H-fuse.

    Standard resistance:
    Below 1 Ω



NG
INSPECT FOR SHORT IN ALL COMPONENTS CONNECTED TO FUSE AND REPAIR OR REPLACE THEM IF NEEDED, AND REPLACE H-FUSE
OK


4.INSPECT TRANSAXLE PARKING LOCK CONTROL RELAY (Marking: P CON RELAY)


    B112776E02
  1. Remove the P CON MTR relay from the engine room relay block.

  1. Measure the resistance of the relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (When battery voltage is applied to terminals 1 and 2)



NG
REPLACE TRANSAXLE PARKING LOCK CONTROL RELAY
OK


5.CHECK WIRE HARNESS (TRANSMISSION CONTROL ECU - BODY GROUND)


    B118155E12
  1. Disconnect the T4 ECU connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    T4-14 (BMA) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU - BODY GROUND)
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (SHIFT CONTROL ACTUATOR - BATTERY) 

6.READ VALUE OF TECHSTREAM (U, V, W VOLTAGE)
  1. Check the Data List for proper functioning of the shift control actuator.

    Shift control actuator 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    U Phase Voltage Value
    U phase voltage value / min: 0 V, max: 20 V
    Actual U phase voltage 9 to 14 V
    -
    V Phase Voltage Value
    V phase voltage value / min: 0 V, max: 20 V
    Actual V phase voltage 9 to 14 V
    -
    W Phase Voltage Value
    W phase voltage value/min: 0 V, max: 20 V
    Actual W phase voltage 9 to 14 V
    -

    Standard voltage:
    9 to 14 V



OK
REPLACE TRANSMISSION CONTROL ECU
NG


7.CHECK WIRE HARNESS (TRANSMISSION CONTROL ECU - SHIFT CONTROL ACTUATOR)


    C126765E02
  1. Disconnect the T4 ECU connector.

  1. Disconnect the S1 actuator connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    T4-10 (MWA) - S1-1 (MWA)
    Below 1 Ω
    T4-11 (MVA) - S1-6 (MVA)
    Below 1 Ω
    T4-12 (MUA) - S1-7 (MUA)
    Below 1 Ω
    T4-10 (MWA) - Body ground
    10 kΩ or higher
    T4-11 (MVA) - Body ground
    10 kΩ or higher
    T4-12 (MUA) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE SHIFT CONTROL ACTUATOR